3.2. Управление пользователями

Switch# ssh -l user1 mgmt-if 192.168.1.1
user1@192.168.1.1's password:
Switch> ena
% No password has been assigned yet
Switch> ?
Exec commands:
  cd          System command cd
  dir         System command ls
  disable     Disable
  enable      Enable
  ethernet    Ethernet Configuration Commands
  exit        Exit from the EXEC
  help        Description of the interactive help system
  logout      Exit from the EXEC
  ls          System command ls
  md5sum      System command md5sum
  no          Negate a command or set its defaults
  ping        Send echo messages
  pwd         System command pwd
  quit        Exit from the EXEC
  ssh         Open a secure shell client connection
  telnet      Open a telnet connection
  terminal    Set terminal line parameters
  traceroute  Trace route to destination
Switch>

Switch# ssh -l user2 mgmt-if 192.168.1.1
user2@192.168.1.1's password:
Switch# ?
Exec commands:
  boot                 Specify boot parameter
  cd                   System command cd
  clear                Reset functions
  cpu-traffic-protect  Set cpu traffic protect
  debug                Debugging functions
  dhcp                 Specify DHCP parameter
  dir                  System command ls
  disable              Disable
  enable               Enable
  ethernet             Ethernet Configuration Commands
  exit                 Exit from the EXEC
  help                 Description of the interactive   help system
  l2                   Layer 2 ping
  logging              Specify logging parameter
  logout               Exit from the EXEC
  ls                   System command ls
  md5sum               System command md5sum
  monitor              Monitoring system traffic
  no                   Negate a command or set its defaults
  ping                 Send echo messages
  pwd                  System command pwd
  quit                 Exit from the EXEC
  set                  Set device attribute
  show                 Show running system information
  ssh                  Open a secure shell client connection
  start                Start vct function
  telnet               Open a telnet connection
  terminal             Set terminal line parameters
  traceroute           Trace route to destination
  udld                 UniDirectional Link Detectional
Switch#

Switch# ssh -l user3 mgmt-if 192.168.1.1
user3@192.168.1.1's password:
Switch# conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# ?
Configure commands:
  acl-statistics           Acl statistics
  arp                      Arp acl configuration
  bfd                      Bidirectional Forwarding Detection (BFD)
  bgp                      Border Gateway Protocol (BGP)
  class-map                Class map command
  clock                    Manage the system clock
  control-plane            Control plane
  cpu-limit                Specify CPU limit configuration, throttle the CPU usage of one process
  cpu-traffic-limit        Set cpu traffic limit characteristics
  cpu-traffic-protect      Set cpu traffic protect
  cpu-traffic-statistics   Set cpu traffic statistics characteristics
  cut-through-forwarding   Cut through forwarding mode
  dhcp                     Specify DHCP parameter
  dhcp-server              Specify DHCP server parameter
  dhcpv6                   Specify DHCPv6 parameter
  dhcpv6-server            Specify DHCPv6 server parameter
  diagnostic               Diagnostic config
  diagnostic-information   diagnostic-information
  dns                      DNS configuration
  do                       To run exec commands in config mode
  dot1x                    IEEE 802.1X Port-Based Access Control
  ecmp                     Equal cost multi-path routing
  efd                      Elephant flow detect
  end                      End current mode and change to EXEC mode
  erps                     Ethernet ring automatic recovery
  errdisable               Error disable
  ethernet                 Configure layer-2
  evpn                     Ethernet VPN
  exit                     End current mode and down to previous mode
  fan                      Fan speed configuration
  ftp                      Specify FTP parameters
  global-acl               Global Acl
  gmrp                     GARP Multicast Registration Protocol
  gratuitous-arp-learning  Gratuitous Arp learning function
  gvrp                     GARP Vlan Registration Protocol
  hardware                 Hardware
  hash-field               Hash field of load balance
  hash-value               Hash value of load balance
  heart-beat-monitor       Heart beat monitor function
  help                     Description of the interactive help system
  hostname                 Set system's network name
  http                     HTTP service
  interface                Select an interface to configure
  ip                       Internet Protocol (IP)
  ipfix                    IP Information Export(IPFIX)
  ipg                      Inter-Packet Gap
  ipv6                     Internet Protocol version 6 (IPv6)
  key                      Authentication key management
  l2protocol               Configure Layer2 Protocol
  lacp                     LACP commands
  led                      Set led mode
  line                     Configure a terminal line
  lldp                     Link Layer Discovery Protocol
  load                     Load configuration
  logging                  Specify logging parameter
  loopback-detect          Loopback Detect Function
  mac                      Global MAC configuration subcommands
  mac-address-table        Configure the MAC address table
  management               Management interface configuration
  max-static-routes        Set maximum static routes number
  max-static-v6routes      Set maximum static IPv6 routes number
  mfp                      Micro Flow Policer(MFP)
  mlag                     Configure MLAG specific attributes
  monitor                  Monitoring system traffic
  monitor-link             Monitor link function
  multi-link               Multi-Link
  mvr                      Enable/Disable MVR on the switch
  mvr6                     Enable/Disable MVR6 on the switch
  no                       Negate a command or set its defaults
  ntp                      NTP configuration
  ospf                     Start OSPF configuration
  overlay                  Configure Overlay parameters
  performance-monitor      Performance Monitor
  poe                      poe layer
  policy-map               Policy map command
  port-bridge              Switch port bridge
  port-channel             EtherChannel commands
  port-group               Port-group
  port-isolate             Port isolate
  priority-flow-control    Priority-Flow-Control
  ptp                      Precision Time Protocol (IEEE1588)
  qos                      Quality of Service
  quit                     Exit current mode and down to previous mode
  raw                      Configure raw vlan group
  reset                    Reset
  rmon                     Remote Monitoring Protocol (RMON)
  route-map                Create route-map or enter route-map command mode
  router                   Enable a routing process
  router-id                Router identifier for this system
  schedule                 Schedule parameters
  selective                Selective qinq type
  service                  Set up miscellaneous service
  sflow                    Sampled flow
  smart-buffer             Smart buffer
  smart-config             SmartConfig
  smart-link               Smart-Link
  snmp-server              Specify SNMP configuration
  spanning-tree            Spanning tree commands
  speed-mode               speed mode
  split                    Split interface
  stack                    Stack
  startup-config           startup config
  stm                      Switch table management
  switch                   Switch media type
  sysmon                   System monitor
  table-map                Configure Table Map
  temperature              Temperature threshold configuration
  time-range               Define time range entries
  track                    Enable a track process
  udld                     UniDirectional Link Detectional
  update                   Update system
  user-define              User define
  vlan                     Configure VLAN parameters
  vlan-group               Vlan-group
  voice                    Voice vlan
  vrrp                     Virtual Redundancy Routing Protocol (VRRP)