2.16. Device Management Commands

2.16.1. temperature

Command Purpose

To specify the system temperature monitor threshold.

Prerequisites

Platform

Software

License

Comments

AQ-N3000

7.0

Base

-

AQ-N5000

7.0

Base

-

AQ-N6000

7.0

Base

-

Command Syntax

termperature LOW HIGH CRITICAL

no termperature

Parameter

Parameter Description

Parameter Value

LOW

Low alarm temperature degree Celsius

45-50, unit:degree Celsius

HIGH

High alarm temperature degree Celsius

50-85, unit:degree Celsius

CRITICAL

Critical alarm temperature degree Celsius

55-100, unit:degree Celsius

Command Mode

Global Config

Default

The default threshold is low temperature 5, high temperature 75, and critical temperature 90.

Usage

The unit for temperature is centigrade.

The critical temperature must higher than high temperature 5 Celsius degrees.

The high temperature must higher than low temperature 5 Celsius degrees.

Examples

This example shows how to specify the temperature thresholds:

Switch# configure terminal
Switch(config)# temperature 5 70 90

2.16.2. show environment

Command Purpose

Use this command to show the hardware environment information.

Prerequisites

Platform

Software

License

Comments

AQ-N3000

7.0

Base

-

AQ-N5000

7.0

Base

-

AQ-N6000

7.0

Base

-

Command Syntax

show environment (slot ID| )

Parameter

Parameter Description

Parameter Value

ID

The ID of stack member.

1 - 29

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This example shows how to display hardware environment information:

Switch# show environment
Fan tray status:
Index Status
1 PRESENT
FanIndex Status SpeedRate Mode
1-1 OK 30% Auto
1-2 OK 30% Auto
1-3 OK 30% Auto
---------------------------------------------------------
Power status:
Index Status Power Type Alert
1 PRESENT OK AC NO
2 ABSENT - - -
---------------------------------------------------------
```console
Sensor status (Degree Centigrade):
Index Temperature Lower_alarm Upper_alarm Critical_limit
1 64 5 75 90

Related Commands

temperature

2.16.3. boot system

Command Purpose

Use this command to specify the system image that the switch loads at startup.

Prerequisites

Platform

Software

License

Comments

AQ-N3000

7.0

Base

-

AQ-N5000

7.0

Base

-

AQ-N6000

7.0

Base

-

Command Syntax

boot system (GFLASHFILE|tftp: mgmt-if IP_ADDR GTFTPFLIE* )

Parameter

Parameter Description

Parameter Value

GFLASHFILE

The file name that will be used to load at startup

File path and name on the flash

IP_ADDR

The tftp server IP address

IPv4 Address

tftp: mgmt-if

Use management port

GTFTPFLIE

The file name that will be used to load at startup

File name on the tftp server

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This example shows how to specify load image from tftp when switch startup:

Switch# boot system tftp: mgmt-if 10.10.29.160 uImage.r

Related Commands

None

2.16.4. show transceiver

Command Purpose

Use this command to show the transceiver information.

Prerequisites

Platform

Software

License

Comments

AQ-N3000

7.0

Base

-

AQ-N5000

7.0

Base

-

AQ-N6000

7.0

Base

-

Command Syntax

show transceiver (interface| ) (detail| )

Parameter

Parameter Description

Parameter Value

interface

Specify the physical interface

detail

Show detail include DDM information

Command Mode

Privileged EXEC

Default

None

Usage

None

Examples

This example shows how to display transceiver information:

Switch# show transceiver detail
Port eth-1-2 transceiver info:
Transceiver Type: 10G Base-SR
Transceiver Vendor Name : OEM
Transceiver PN : SFP-10GB-SR
Transceiver S/N : 201033PST1077C
Transceiver Output Wavelength: 850 nm
Supported Link Type and Length:
Link Length for 50/125um multi-mode fiber: 80 m
Link Length for 62.5/125um multi-mode fiber: 30 m
 ----------------------------------------------------------------------------
Transceiver is internally calibrated.
mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.
 ++ : high alarm, + : high warning, - : low warning, -- : low alarm.
The threshold values are calibrated.
 ----------------------------------------------------------------------------
High Alarm High Warn Low Warn Low Alarm
Temperature Threshold Threshold Threshold Threshold
Port (Celsius) (Celsius) (Celsius) (Celsius) (Celsius)
------------- ---------- --------- --------- ----------
eth-1-2 25.92 95.00       90.00     -20.00    -25.00
 --------------------------------------------------------------------------------------------------
High Alarm High Warn Low Warn Low Alarm
Voltage Threshold Threshold Threshold Threshold
Port (Volts) (Volts) (Volts) (Volts) (Volts)
------------ --------------- ----------------
eth-1-2 3.32 3.80   3.70      2.90 2.80
---------------------------------------------------------------------------------------------------

High Alarm High Warn Low Warn Low Alarm
Current Threshold Threshold Threshold Threshold
Port (milliamperes) (mA) (mA) (mA) (mA)
------------------ ----------------------
eth-1-2 6.41        20.00 18.00 1.00 0.50
-----------------------------------------------------------------------------------------------------
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm)    (dBm) (dBm) (dBm) (dBm)
--------- --------------------------
eth-1-2 -2.41 2.01  1.00  -6.99 -7.96
-------------------------------------------------------------------------------------------------------
Optical High Alarm High Warn Low Warn Low Alarm
Receive Power Threshold Threshold Threshold Threshold
Port (dBm)   (dBm) (dBm) (dBm) (dBm)
-----------  -----------------------
eth-1-2 -12 - 1.00 0.00 -19.00 -20.00
-------------------------------------------------------------------------------------------------------

Related Commands

None

2.16.5. update bootrom

Command Purpose

Use this command to update bootrom image.

Prerequisites

Platform

Software

License

Comments

AQ-N3000

7.0

Base

-

AQ-N5000

7.0

Base

-

AQ-N6000

7.0

Base

-

Command Syntax

update bootrom (flash|udisk)

Parameter

Parameter Description

Parameter Value

flash

Source file direction

-

udisk

Source file direction

-

Command Mode

Global Config

Default

None

Usage

None

Examples

This example shows how to update bootrom image:

Switch# configure terminal
Switch(config)# update bootrom flash:/boot/ bootrom.bin

Related Commands

None

2.16.6. show reboot-info

Command Purpose

Use this command to show reboot info.

Prerequisites

Platform

Software

License

Comments

AQ-N3000

7.0

Base

-

AQ-N5000

7.0

Base

-

AQ-N6000

7.0

Base

-

Command Syntax

show reboot-info (slot ID| )

Parameter

Parameter Description

Parameter Value

ID

The ID of stack member

1 - 29

Command Mode

Privileged EXEC

Default

None

Usage

Reboot Type

Description

POWER

Power outages

MANUAL

Cli U8220 reboot/reload U8221 undersystem

HIGH-TMPR

Reboot for abnormal high temperature

BHMDOG

BHM watchdog, monitor functional module

LCMDOG

LCM watchdog, monitor each LC

SCHEDULE

Schedule reboot

SNMP-RELOAD

SNMP reboot

HALFAIL

Reboot for HAGT communicate with HSRV failedUnicodeFF0Cneed stack enable

ABNORMAL

Unusual reboot, include reboot under shell

CTCINTR

Button reboot

LCATTACH

Reboot for LC attach CHSM failed

OTHER

Other reboot

OTHER

Other reboot

Examples

This example shows how to show reboot-info:

Switch# show reboot-info
Times Reboot    Type Reboot     Time (UTC)
--------------+---------------+--------------------
1               MANUAL          2023-01-04 20:54:22
2               MANUAL          2023-01-04 21:00:30
3               MANUAL          2023-01-04 21:06:53
4               MANUAL          2023-01-04 21:10:13
5               MANUAL          2023-01-04 21:14:16
6               MANUAL          2023-01-04 21:20:50

Related Commands

None