AqNOS Command Reference Guide

Contents

• 1. Preface
  • 1.1. Suggestion feedback
  • 1.2. Audience
  • 1.3. Conventions
  • 1.4. Declaration
• 2. Basic Commands
  • 2.1. System Configuration Commands
    • 2.1.1. hostname
    • 2.1.2. management ip address
    • 2.1.3. management route
    • 2.1.4. show management arp
    • 2.1.5. show management ip address
    • 2.1.6. show management interface
    • 2.1.7. clear counters mgmt-if
    • 2.1.8. enable password
    • 2.1.9. terminal length
    • 2.1.10. service terminal-length
    • 2.1.11. banner motd
    • 2.1.12. banner exec
    • 2.1.13. banner login
    • 2.1.14. show version
    • 2.1.15. line vty
    • 2.1.16. line-password
    • 2.1.17. exec-timeout
    • 2.1.18. access-class
    • 2.1.19. ipv6 access-class
    • 2.1.20. reboot
    • 2.1.21. schedule reboot at
    • 2.1.22. schedule reboot delay
    • 2.1.23. boot system
    • 2.1.24. show boot
    • 2.1.25. show boot images
    • 2.1.26. show memory
    • 2.1.27. show cpu traffic-limit
    • 2.1.28. show processes cpu sorted
    • 2.1.29. show processes cpu history
    • 2.1.30. show processes memory sorted
    • 2.1.31. terminal monitor
    • 2.1.32. configure terminal
    • 2.1.33. disable
    • 2.1.34. enable
    • 2.1.35. end
    • 2.1.36. exit (global)
    • 2.1.37. exit (EXEC)
    • 2.1.38. quit
    • 2.1.39. cd
    • 2.1.40. copy
    • 2.1.41. delete
    • 2.1.42. dir
    • 2.1.43. ls
    • 2.1.44. more
    • 2.1.45. mkdir
    • 2.1.46. rename
    • 2.1.47. rmdir
    • 2.1.48. tar create
    • 2.1.49. tar table
    • 2.1.50. tar xtract
    • 2.1.51. show diagnostic-information
    • 2.1.52. tar diagnostic-information
    • 2.1.53. format
    • 2.1.54. umount
    • 2.1.55. cut-through enable
    • 2.1.56. show cut-through-forwarding mode
    • 2.1.57. reset factory-config
    • 2.1.58. show factory-config
    • 2.1.59. show this
    • 2.1.60. show route-mac
    • 2.1.61. show history
  • 2.2. User Management Commands
    • 2.2.1. username
    • 2.2.2. username password
    • 2.2.3. username secret
    • 2.2.4. username privilege
    • 2.2.5. username service-type
    • 2.2.6. username privilege password
    • 2.2.7. re-username newname
    • 2.2.8. cipher detect
  • 2.3. FTP Commands
    • 2.3.1. ftp
    • 2.3.2. ftp vrf
    • 2.3.3. ftp passive
    • 2.3.4. show ftp
    • 2.3.5. copy GFILENAME GURLNAME
    • 2.3.6. copy GURLNAME GFILENAME
  • 2.4. FTP server Commands
    • 2.4.1. ftp server enable
    • 2.4.2. ftp server port
    • 2.4.3. ftp server time-out
    • 2.4.4. ftp server source address
    • 2.4.5. show ftp server
  • 2.5. TFTP Commands
    • 2.5.1. copy GFILENAME GURLNAME
    • 2.5.2. copy GURLNAME GFILENAME
    • 2.5.3. copy running-config mgmt-if
    • 2.5.4. copy mgmt-if startup-config
  • 2.6. scp Commands
    • 2.6.1. copy GFILENAME GURLNAME
    • 2.6.2. copy GURLNAME GFILENAME
    • 2.6.3. copy running-config mgmt-if
    • 2.6.4. copy mgmt-if startup-config
  • 2.7. Telnet Commands
    • 2.7.1. telnet
    • 2.7.2. ip telnet server source address
    • 2.7.3. ip telnet server source port
    • 2.7.4. ip telnet server source mgmt-if port
  • 2.8. SSH Commands
    • 2.8.1. ip ssh server
    • 2.8.2. ip ssh server authentication-retries
    • 2.8.3. ip ssh server authentication-timeout
    • 2.8.4. ip ssh server authentication-type
    • 2.8.5. ip ssh server host-key rsa key
    • 2.8.6. ip ssh server rekey-interval
    • 2.8.7. ip ssh server version
    • 2.8.8. ip ssh server source address
    • 2.8.9. ip ssh server source port
    • 2.8.10. ip ssh server source mgmt-if port
    • 2.8.11. show ip ssh server status
    • 2.8.12. rsa key generate
    • 2.8.13. rsa key
    • 2.8.14. key format
    • 2.8.15. key string end
    • 2.8.16. key type
    • 2.8.17. reset
    • 2.8.18. validate
    • 2.8.19. KEYLINE
    • 2.8.20. rsa key export
    • 2.8.21. rsa key import
    • 2.8.22. show rsa key
    • 2.8.23. show rsa keys
  • 2.9. Time&Timezone Commands
    • 2.9.1. clock set datetime
    • 2.9.2. clock set timezone
    • 2.9.3. clock set summer-time
    • 2.9.4. show clock
    • 2.9.5. show timezones
  • 2.10. HTTP commands Commands
    • 2.10.1. service http
    • 2.10.2. service https
    • 2.10.3. http server load
    • 2.10.4. http timeout
    • 2.10.5. http server source address
    • 2.10.6. http server source port
    • 2.10.7. http server source ssl-port
    • 2.10.8. http server source mgmt-if port
    • 2.10.9. http server source mgmt-if ssl-port
    • 2.10.10. http authentication aaa
    • 2.10.11. show services http
  • 2.11. RPC-API commands Commands
    • 2.11.1. service rpc-api
    • 2.11.2. service rpc-api auth-mode
    • 2.11.3. show services rpc-api
  • 2.12. DIAG Commands
    • 2.12.1. diagnostic-information discard
    • 2.12.2. show diagnostic-information discard
  • 2.13. STM Commands
    • 2.13.1. stm prefer
    • 2.13.2. show stm prefer
  • 2.14. Syslog Commands
    • 2.14.1. clear logging buffer
    • 2.14.2. logging alarm-trap
    • 2.14.3. logging file
    • 2.14.4. logging level file
    • 2.14.5. logging buffer
    • 2.14.6. logging level module
    • 2.14.7. logging merge
    • 2.14.8. logging sync
    • 2.14.9. logging sync timeout
    • 2.14.10. logging operate
    • 2.14.11. logging server
    • 2.14.12. logging server address
    • 2.14.13. logging server facility
    • 2.14.14. logging server severity
    • 2.14.15. logging timestamp
    • 2.14.16. show logging
    • 2.14.17. show logging buffer
  • 2.15. Mirror Commands
    • 2.15.1. monitor session destination interface
    • 2.15.2. monitor session destination cpu
    • 2.15.3. monitor session destination group
    • 2.15.4. member
    • 2.15.5. monitor session source interface
    • 2.15.6. monitor session source vlan
    • 2.15.7. monitor session source cpu
    • 2.15.8. monitor session destination interface tunnel
    • 2.15.9. monitor session destination remote
    • 2.15.10. monitor mac escape
    • 2.15.11. show monitor
    • 2.15.12. show monitor mac escape
    • 2.15.13. monitor destination forwarding enable
    • 2.15.14. monitor cpu set packet buffer
    • 2.15.15. monitor cpu capture packet
    • 2.15.16. monitor cpu capture strategy
    • 2.15.17. show monitor cpu packet
    • 2.15.18. clear monitor cpu packet all
    • 2.15.19. show monitor cpu packet buffer-size
    • 2.15.20. show monitor cpu capture strategy
  • 2.16. Device Management Commands
    • 2.16.1. temperature
    • 2.16.2. show environment
    • 2.16.3. boot system
    • 2.16.4. show transceiver
    • 2.16.5. update bootrom
    • 2.16.6. show reboot-info
  • 2.17. Bootrom Commands
    • 2.17.1. version
    • 2.17.2. setenv
    • 2.17.3. saveenv
    • 2.17.4. printenv
    • 2.17.5. reset
    • 2.17.6. ping
    • 2.17.7. aqcls
    • 2.17.8. boot_tftp
    • 2.17.9. boot_tftp_nopass
    • 2.17.10. boot_flash
    • 2.17.11. boot_flash_nopass
    • 2.17.12. upgrade_uboot
  • 2.18. SmartConfig Commands
    • 2.18.1. smart-config
    • 2.18.2. show smart-config config
• 3. Ethernet Commands
  • 3.1. Interface Commands
    • 3.1.1. bandwidth
    • 3.1.2. clear counters
    • 3.1.3. description
    • 3.1.4. duplex
    • 3.1.5. speed
    • 3.1.6. group-speed
    • 3.1.7. interface
    • 3.1.8. interface range
    • 3.1.9. interface range create vlan
    • 3.1.10. jumboframe
    • 3.1.11. media-type
    • 3.1.12. unidirectional
    • 3.1.13. shutdown
    • 3.1.14. split interface
    • 3.1.15. load-interval
    • 3.1.16. vlan dot1q tag native
    • 3.1.17. show interface
    • 3.1.18. show interface status
    • 3.1.19. show interface summary
    • 3.1.20. show ip interface
    • 3.1.21. switchport
    • 3.1.22. switchport access allowed
    • 3.1.23. switchport access vlan
    • 3.1.24. switchport mode access
    • 3.1.25. switchport mode trunk
    • 3.1.26. switchport mode dot1q-tunnel
    • 3.1.27. switchport trunk allowed
    • 3.1.28. switchport trunk native vlan
    • 3.1.29. switchport port-bridge enable
    • 3.1.30. port-bridge enable
    • 3.1.31. port-xconnect
    • 3.1.32. carrier up-hold-time interval
    • 3.1.33. carrier down-hold-time interval
    • 3.1.34. mtu
    • 3.1.35. wavelength freq
    • 3.1.36. fec
    • 3.1.37. mdi
    • 3.1.38. show group-id info
  • 3.2. Interface Errdisable Commands
    • 3.2.1. errdisable detect
    • 3.2.2. errdisable recovery interval
    • 3.2.3. errdisable fdb-loop count
    • 3.2.4. errdisable fdb-loop exclude-vlan
    • 3.2.5. errdisable recovery reason
    • 3.2.6. errdisable flap
    • 3.2.7. show errdisable detect
    • 3.2.8. show errdisable recovery
    • 3.2.9. show errdisable flap
    • 3.2.10. show errdisable fdb-loop
    • 3.2.11. errdisable fdb-loop trust
  • 3.3. MAC Address Table Commands
    • 3.3.1. mac-address-table aging-time
    • 3.3.2. mac-address-table hardware-learning
    • 3.3.3. mac-address-table forward
    • 3.3.4. mac-address-table discard
    • 3.3.5. clear mac address-table
    • 3.3.6. port-bridge
    • 3.3.7. show mac address-table aging-time
    • 3.3.8. show mac address-table
    • 3.3.9. show mac address-table hardware
    • 3.3.10. show mac address-table count
    • 3.3.11. show mac address-table hardware count
    • 3.3.12. show mac address-table add-fdb-fail
    • 3.3.13. show mac-filter address-table
    • 3.3.14. show resource mac-filter
    • 3.3.15. show resource static-fdb
    • 3.3.16. mac-address-table discard vlan
    • 3.3.17. clear mac address-table blackhole
    • 3.3.18. show mac address-table
  • 3.4. VLAN Commands
    • 3.4.1. vlan database
    • 3.4.2. vlan
    • 3.4.3. vlan VLAN_LIST
    • 3.4.4. show vlan
    • 3.4.5. show vlan all
    • 3.4.6. show vlan brief
    • 3.4.7. show interface switchport
    • 3.4.8. switchport access allowed
    • 3.4.9. switchport access vlan
    • 3.4.10. switchport mode access
    • 3.4.11. switchport mode trunk
    • 3.4.12. switchport trunk allowed
    • 3.4.13. switchport trunk native
    • 3.4.14. switchport trunk unatgged vlan
    • 3.4.15. vlan bridge disable
    • 3.4.16. vlan statistics enable
    • 3.4.17. vlan statistics interval
    • 3.4.18. clear vlan statistics
    • 3.4.19. show vlan statistics
    • 3.4.20. show resource vlan-stats
    • 3.4.21. vlan statistics include-interframe
  • 3.5. Voice VLAN Commands
    • 3.5.1. voice vlan
    • 3.5.2. voice vlan security enable
    • 3.5.3. voice vlan set cos to
    • 3.5.4. voice vlan mac-address
    • 3.5.5. voice vlan enable
    • 3.5.6. show voice vlan state
  • 3.6. Link Aggregation Commands
    • 3.6.1. channel-group
    • 3.6.2. static-channel-group
    • 3.6.3. distribute-weight
    • 3.6.4. lacp max-active-linknumber
    • 3.6.5. lacp preempt enable
    • 3.6.6. lacp preempt delay
    • 3.6.7. lacp port-id extend
    • 3.6.8. lacp port-priority
    • 3.6.9. lacp timeout
    • 3.6.10. lacp system-priority
    • 3.6.11. lacp mlag system-id
    • 3.6.12. port-channel channel-group-number load-balance-mode dynamic
    • 3.6.13. port-channel channel-group-number load-balance-mode resilient
    • 3.6.14. port-channel channel-group-number load-balance-mode round-robin
    • 3.6.15. port-channel channel-group-number self-healing
    • 3.6.16. port-channel channel-group-number session-preservation
    • 3.6.17. port-channel channel-group-number static
    • 3.6.18. port-channel channel-group-number lacp-mode dynamic
    • 3.6.19. port-channel group-mode
    • 3.6.20. local-preference
    • 3.6.21. show channel-group summary
    • 3.6.22. show channel-group detail
    • 3.6.23. show lacp internal
    • 3.6.24. show lacp internal detail
    • 3.6.25. show lacp neighbor
    • 3.6.26. show lacp neighbor detail
    • 3.6.27. show channel-group port
    • 3.6.28. show lacp counters
    • 3.6.29. show lacp sys-id
    • 3.6.30. clear lacp counters
    • 3.6.31. debug lacp
    • 3.6.32. show debugging lacp
  • 3.7. VLAN Classification Commands
    • 3.7.1. vlan classifier activate
    • 3.7.2. vlan classifier group
    • 3.7.3. vlan classifier rule
    • 3.7.4. vlan classifier default-action
    • 3.7.5. show vlan classifier group
    • 3.7.6. show vlan classifier interface
    • 3.7.7. show vlan classifier rule
    • 3.7.8. show resource vlan-classification
  • 3.8. VLAN Mapping Commands
    • 3.8.1. ethernet evc
    • 3.8.2. dot1q mapped-vlan
    • 3.8.3. dot1q mapped-double-vlan
    • 3.8.4. vlan mapping table
    • 3.8.5. raw vlan group
    • 3.8.6. raw-vlan
    • 3.8.7. dot1q ethertype
    • 3.8.8. show vlan mapping table
    • 3.8.9. show vlan mapping table applied-interface
    • 3.8.10. switchport mode
    • 3.8.11. switchport dot1q-tunnel type
    • 3.8.12. switchport dot1q-tunnel native
    • 3.8.13. switchport dot1q-tunnel allow vlan
    • 3.8.14. switchport dot1q-tunnel vlan mapping table
    • 3.8.15. switchport dot1q-tunnel vlan mapping miss-forward
    • 3.8.16. switchport trunk vlan-translation
    • 3.8.17. switchport trunk vlan-translation mapping table
    • 3.8.18. switchport trunk vlan-translation miss-forward
    • 3.8.19. vlan dot1q tag native
    • 3.8.20. show resource vlan-mapping
  • 3.9. MSTP Commands
    • 3.9.1. spanning-tree enable
    • 3.9.2. spanning-tree priority
    • 3.9.3. spanning-tree instance priority
    • 3.9.4. spanning-tree forward-time
    • 3.9.5. spanning-tree hello-time
    • 3.9.6. spanning-tree max-age
    • 3.9.7. spanning-tree max-hops
    • 3.9.8. spanning-tree transmit-holdcount
    • 3.9.9. spanning-tree edgeport bpdu-guard (Global)
    • 3.9.10. spanning-tree edgeport bpdu-filter (Global)
    • 3.9.11. spanning-tree port
    • 3.9.12. spanning-tree port-priority
    • 3.9.13. spanning-tree pathcost-standard
    • 3.9.14. spanning-tree path-cost
    • 3.9.15. spanning-tree link-type
    • 3.9.16. spanning-tree edgeport
    • 3.9.17. spanning-tree edgeport bpdu-guard (Interface)
    • 3.9.18. spanning-tree edgeport bpdu-filter (Interface)
    • 3.9.19. spanning-tree guard root
    • 3.9.20. spanning-tree guard loop
    • 3.9.21. spanning-tree bpdu-loop
    • 3.9.22. spanning-tree force-version
    • 3.9.23. spanning-tree restricted-tcn
    • 3.9.24. spanning-tree restricted-role
    • 3.9.25. spanning-tree tc-protection
    • 3.9.26. spanning-tree tc-protection threshold
    • 3.9.27. spanning-tree mode
    • 3.9.28. spanning-tree instance port-priority
    • 3.9.29. spanning-tree instance path-cost
    • 3.9.30. spanning-tree instance restricted-tcn
    • 3.9.31. spanning-tree instance restricted-role
    • 3.9.32. spanning-tree mst configuration
    • 3.9.33. instance
    • 3.9.34. region
    • 3.9.35. revision
    • 3.9.36. clear spanning-tree detected protocols
    • 3.9.37. clear spanning-tree disabled-port
    • 3.9.38. show spanning-tree
    • 3.9.39. show spanning-tree interface
    • 3.9.40. show spanning-tree brief
    • 3.9.41. show spanning-tree disabled-port
    • 3.9.42. show spanning-tree mst
    • 3.9.43. show spanning-tree mst config
    • 3.9.44. show spanning-tree mst detail
    • 3.9.45. show spanning-tree mst instance
    • 3.9.46. show spanning-tree mst interface
    • 3.9.47. show spanning-tree mst brief
    • 3.9.48. spanning-tree instance forward
  • 3.10. Flow Control Commands
    • 3.10.1. flowcontrol send
    • 3.10.2. flowcontrol receive
    • 3.10.3. show flowcontrol
  • 3.11. Layer 2 Protocols Tunneling Commands
    • 3.11.1. l2protocol enable
    • 3.11.2. l2protocol tunnel-dmac
    • 3.11.3. l2protocol mac 1
    • 3.11.4. l2protocol mac
    • 3.11.5. l2protocol
    • 3.11.6. l2protocol uplink enable
    • 3.11.7. show l2protocol
    • 3.11.8. l2protocol cos
    • 3.11.9. l2protocol full-mac
  • 3.12. Storm Control Commands
    • 3.12.1. port storm-control
    • 3.12.2. vlan storm-control
    • 3.12.3. ipg storm-control enable
    • 3.12.4. show storm-control
    • 3.12.5. show storm-control resource
  • 3.13. Loopback Detection Commands
    • 3.13.1. loopback-detect enable
    • 3.13.2. loopback-detect packet-interval
    • 3.13.3. loopback-detect recovery-time
    • 3.13.4. loopback-detect delay-time
    • 3.13.5. loopback-detect action
    • 3.13.6. loopback-detect packet vlan
    • 3.13.7. show loopback-detect
    • 3.13.8. loopback-detect in-loop-enable
  • 3.14. MLAG Commands
    • 3.14.1. mlag configuration
    • 3.14.2. peer-address
    • 3.14.3. peer-link
    • 3.14.4. timers mlag
    • 3.14.5. reload-delay
    • 3.14.6. sync-orphan
    • 3.14.7. sync-overlay
    • 3.14.8. mlag
    • 3.14.9. clear mlag count
    • 3.14.10. show mlag
    • 3.14.11. show mlag peer
    • 3.14.12. show mlag interface
  • 3.15. Hash load-banlance Commands
    • 3.15.1. hash field
    • 3.15.2. l2
    • 3.15.3. ip
    • 3.15.4. ipv6
    • 3.15.5. vxlan
    • 3.15.6. nvgre
    • 3.15.7. show hash-value
    • 3.15.8. show hash-value interface-applied
    • 3.15.9. hash-value global
    • 3.15.10. show hash-value global
    • 3.15.11. disable ecmp round-robin
    • 3.15.12. disable port-channel round-robin
• 4. IP Service Commands
  • 4.1. ARP Commands
    • 4.1.1. arp
    • 4.1.2. arp retry-interval
    • 4.1.3. arp timeout
    • 4.1.4. arp as-layer-3 enable
    • 4.1.5. arp fake global enable
    • 4.1.6. arp fake enable
    • 4.1.7. arp fake timeout
    • 4.1.8. clear arp-cache
    • 4.1.9. clear ip arp
    • 4.1.10. clear ip arp statistics
    • 4.1.11. show ip arp
    • 4.1.12. show ip arp summary
    • 4.1.13. debug arp
    • 4.1.14. show debugging arp
    • 4.1.15. proxy-arp enable
    • 4.1.16. local-proxy-arp enable
    • 4.1.17. gratuitous-arp-learning enable
    • 4.1.18. gratuitous-arp send interval
    • 4.1.19. gratuitous-arp send enable
  • 4.2. DHCP Client Commands
    • 4.2.1. ip address dhcp
    • 4.2.2. management ip address dhcp
    • 4.2.3. dhcp client request
    • 4.2.4. dhcp client client-id
    • 4.2.5. dhcp client class-id
    • 4.2.6. dhcp client lease
    • 4.2.7. dhcp client hostname
    • 4.2.8. dhcp client default-router distance
    • 4.2.9. dhcp client broadcast-flag
    • 4.2.10. debug dhcp client
    • 4.2.11. show dhcp client
    • 4.2.12. show dhcp client statistics
    • 4.2.13. clear dhcp client statistics
  • 4.3. DHCP Relay Commands
    • 4.3.1. dhcp relay
    • 4.3.2. dhcp-server (global)
    • 4.3.3. dhcp-server (interface)
    • 4.3.4. dhcp relay information check
    • 4.3.5. dhcp relay information option
    • 4.3.6. dhcp relay information policy
    • 4.3.7. dhcp relay information policy (interface)
    • 4.3.8. dhcp relay information trust-all
    • 4.3.9. dhcp relay information trusted
    • 4.3.10. dhcp relay gateway
    • 4.3.11. dhcp relay address cycle
    • 4.3.12. service dhcp
    • 4.3.13. debug dhcp relay
    • 4.3.14. show dhcp-server
    • 4.3.15. show dhcp relay interfaces
    • 4.3.16. show dhcp relay information config
    • 4.3.17. show dhcp relay information trusted-sources
    • 4.3.18. show dhcp relay statistics
    • 4.3.19. clear dhcp relay statistics
  • 4.4. DHCP Server Commands
    • 4.4.1. service dhcp
    • 4.4.2. dhcp-server (global)
    • 4.4.3. dhcp-server (interface)
    • 4.4.4. dhcp ping packets
    • 4.4.5. dhcp ping timeout
    • 4.4.6. dhcp pool
    • 4.4.7. static-bind
    • 4.4.8. dns-server address
    • 4.4.9. domain-name
    • 4.4.10. bootfile-name
    • 4.4.11. tftp-server-address
    • 4.4.12. gateway address
    • 4.4.13. netbios-name-server
    • 4.4.14. netbios-node-type
    • 4.4.15. network
    • 4.4.16. lease
    • 4.4.17. option
    • 4.4.18. dhcp excluded-address
    • 4.4.19. show dhcp server conflict
    • 4.4.20. show dhcp server binding
    • 4.4.21. show dhcp server statistics
    • 4.4.22. clear dhcp server conflict
    • 4.4.23. clear dhcp server binding
    • 4.4.24. clear dhcp server statistics
    • 4.4.25. show dhcp server pool
  • 4.5. DNS Commands
    • 4.5.1. ip host
    • 4.5.2. dns domain
    • 4.5.3. dns server
    • 4.5.4. show dns
    • 4.5.5. show ip host
• 5. IPv6 Service Commands
  • 5.1. Tunnel Commands
    • 5.1.1. interface
    • 5.1.2. tunnel mode
    • 5.1.3. tunnel source
    • 5.1.4. tunnel destination
    • 5.1.5. tunnel enable
    • 5.1.6. tunnel ecmp-destination
    • 5.1.7. tunnel gre key
    • 5.1.8. tunnel extend-header
    • 5.1.9. tunnel extend-header id
    • 5.1.10. tunnel dscp
    • 5.1.11. tunnel ttl
    • 5.1.12. ipv6 mtu
    • 5.1.13. show interface tunnel
    • 5.1.14. show resource tunnel
  • 5.2. NDP Commands
    • 5.2.1. ipv6 neighbor
    • 5.2.2. clear ipv6 neighbors
    • 5.2.3. ipv6 hop-limit
    • 5.2.4. ipv6 nd ra hop-limit
    • 5.2.5. ipv6 nd dad attempts
    • 5.2.6. ipv6 nd ns-interval
    • 5.2.7. ipv6 nd ra suppress
    • 5.2.8. ipv6 nd ra mtu suppress
    • 5.2.9. ipv6 nd ra interval
    • 5.2.10. ipv6 nd ra lifetime
    • 5.2.11. ipv6 nd reachable-time
    • 5.2.12. ipv6 nd managed-config-flag
    • 5.2.13. ipv6 nd other-config-flag
    • 5.2.14. ipv6 nd prefix
    • 5.2.15. show ipv6 interface IFNAME prefix
    • 5.2.16. show ipv6 neighbors
    • 5.2.17. debug ipv6 nd
  • 5.3. DHCPv6 Relay Commands
    • 5.3.1. dhcpv6 relay
    • 5.3.2. dhcpv6-server (global)
    • 5.3.3. dhcpv6-server (interface)
    • 5.3.4. dhcpv6 relay remote-id option
    • 5.3.5. dhcpv6 relay remote-id format
    • 5.3.6. dhcpv6 relay pd route
    • 5.3.7. dhcpv6 relay pd route distance
    • 5.3.8. service dhcpv6
    • 5.3.9. debug dhcpv6 relay
    • 5.3.10. show dhcpv6-server
    • 5.3.11. show dhcpv6 relay interfaces
    • 5.3.12. show dhcpv6 relay pd client
    • 5.3.13. show dhcpv6 relay statistics
    • 5.3.14. clear dhcpv6 relay statistics
    • 5.3.15. clear dhcpv6 relay pd route
• 6. IP Routing Commands
  • 6.1. IP Unicast-Routing Commands
    • 6.1.1. ip address
    • 6.1.2. ip icmp error-interval
    • 6.1.3. ip redirects
    • 6.1.4. ip unreachables
    • 6.1.5. ip verify unicast reverse-path
    • 6.1.6. unicast reverse-path check-type (strict| loose (allow-default-route|))
    • 6.1.7. router-id (global)
    • 6.1.8. ip route
    • 6.1.9. show ip route
    • 6.1.10. show ip route database
    • 6.1.11. show ip protocols
    • 6.1.12. show ip route summary
    • 6.1.13. show ip route add-fib-fail
    • 6.1.14. max-static-routes
    • 6.1.15. show resource fib
    • 6.1.16. ecmp load-balance-mode dynamic
    • 6.1.17. ecmp load-balance-mode dynamic (efd-only|tcp-only)
    • 6.1.18. ecmp load-balance-mode static
    • 6.1.19. ecmp load-balance-mode static self-healing
    • 6.1.20. ecmp load-balance-mode round-robin
    • 6.1.21. show ecmp information
  • 6.2. RIP Commands
    • 6.2.1. default-information originate (RIP)
    • 6.2.2. default-metric (RIP)
    • 6.2.3. distance (RIP)
    • 6.2.4. ip rip authentication
    • 6.2.5. ip rip authentication mode
    • 6.2.6. ip rip receive version
    • 6.2.7. ip rip receive-packet
    • 6.2.8. ip rip send version
    • 6.2.9. ip rip send-packet
    • 6.2.10. ip rip split-horizon
    • 6.2.11. network (RIP)
    • 6.2.12. neighbor (RIP)
    • 6.2.13. offset-list (RIP)
    • 6.2.14. passive-interface (RIP)
    • 6.2.15. redistribute (RIP)
    • 6.2.16. router rip
    • 6.2.17. timers basic (RIP)
    • 6.2.18. show ip rip database
    • 6.2.19. show ip rip interface
    • 6.2.20. version (RIP)
    • 6.2.21. distribute-list
    • 6.2.22. address-family
    • 6.2.23. show ip protocol rip
    • 6.2.24. debug rip
    • 6.2.25. show debugging rip
    • 6.2.26. show ip rip database database-summary
    • 6.2.27. show resource rip
  • 6.3. OSPF Commands
    • 6.3.1. area authentication
    • 6.3.2. area default-cost
    • 6.3.3. area filter-list
    • 6.3.4. area range
    • 6.3.5. area stub
    • 6.3.6. area nssa
    • 6.3.7. auto-cost
    • 6.3.8. clear ip ospf
    • 6.3.9. compatible rfc1583
    • 6.3.10. default-information originate (OSPF)
    • 6.3.11. default-metric (OSPF)
    • 6.3.12. distance (OSPF)
    • 6.3.13. distribute-list (OSPF)
    • 6.3.14. distribute-list (OSPF)
    • 6.3.15. ip ospf authentication
    • 6.3.16. ip ospf authentication-key
    • 6.3.17. ip ospf cost
    • 6.3.18. ip ospf database-filter all out
    • 6.3.19. ip ospf dead-interval
    • 6.3.20. ip ospf hello-interval
    • 6.3.21. ip ospf message-digest-key md5
    • 6.3.22. ip ospf mtu
    • 6.3.23. ip ospf mtu-ignore
    • 6.3.24. ip ospf priority
    • 6.3.25. ip ospf retransmit-interval
    • 6.3.26. ip ospf transmit-delay
    • 6.3.27. ip ospf network
    • 6.3.28. neighbor (OSPF)
    • 6.3.29. network area (OSPF)
    • 6.3.30. overflow database external
    • 6.3.31. passive-interface (OSPF)
    • 6.3.32. redistribute (OSPF)
    • 6.3.33. router-id (OSPF)
    • 6.3.34. router ospf
    • 6.3.35. summary-address (OSPF)
    • 6.3.36. show ip ospf
    • 6.3.37. show ip ospf border-routers
    • 6.3.38. show ip ospf database
    • 6.3.39. show ip ospf interface
    • 6.3.40. show ip ospf neighbor
    • 6.3.41. show ip ospf summary-address
    • 6.3.42. show ip ospf route summary
    • 6.3.43. show ip protocols ospf
    • 6.3.44. show ip ospf processes-count
    • 6.3.45. timers spf
    • 6.3.46. max-concurrent-dd
    • 6.3.47. maximum-area
    • 6.3.48. refresh timer
    • 6.3.49. ip ospf bfd
    • 6.3.50. debug ospf
    • 6.3.51. debug ospf bfd
    • 6.3.52. debug ospf events
    • 6.3.53. debug ospf ifsm
    • 6.3.54. debug ospf nfsm
    • 6.3.55. debug ospf lsa
    • 6.3.56. debug ospf packet
    • 6.3.57. debug ospf route
    • 6.3.58. show debugging ospf
    • 6.3.59. show resource ospf
    • 6.3.60. min-lsa-interval
  • 6.4. Route Map Commands
    • 6.4.1. route-map
    • 6.4.2. match as-path
    • 6.4.3. match community
    • 6.4.4. match interface
    • 6.4.5. match ip address
    • 6.4.6. match ip address prefix-list
    • 6.4.7. match ip next-hop
    • 6.4.8. match ip next-hop prefix-list
    • 6.4.9. match local-preference
    • 6.4.10. match metric
    • 6.4.11. match origin
    • 6.4.12. match route-type external
    • 6.4.13. match tag
    • 6.4.14. set aggregator
    • 6.4.15. set as-path
    • 6.4.16. set atomic-aggregate
    • 6.4.17. set comm-list delete
    • 6.4.18. set community
    • 6.4.19. set dampening
    • 6.4.20. set extcommunity
    • 6.4.21. set ip next-hop
    • 6.4.22. set ip vrf next-hop
    • 6.4.23. set ip default next-hop
    • 6.4.24. set ip default vrf next-hop
    • 6.4.25. set local-preference
    • 6.4.26. set metric
    • 6.4.27. set metric-type
    • 6.4.28. set origin
    • 6.4.29. set originator-id
    • 6.4.30. set tag
    • 6.4.31. set vpnv4 next-hop
    • 6.4.32. set weight
    • 6.4.33. show route-map
  • 6.5. Prefix-list Commands
    • 6.5.1. ip prefix-list
    • 6.5.2. ip prefix-list description
    • 6.5.3. ip prefix-list sequence-number
    • 6.5.4. show ip prefix-list
    • 6.5.5. clear ip prefix-list
  • 6.6. Policy-Based Routing Commands
    • 6.6.1. ip policy route-map
    • 6.6.2. ip-group
    • 6.6.3. ip-member
    • 6.6.4. show ip policy route-map
    • 6.6.5. show resource pbr
  • 6.7. BGP Commands
    • 6.7.1. address-family
    • 6.7.2. aggregate-address
    • 6.7.3. bgp always-compare-med
    • 6.7.4. bgp bestpath as-path ignore
    • 6.7.5. bgp bestpath compare-confed-aspath
    • 6.7.6. bgp bestpath compare-routerid
    • 6.7.7. bgp bestpath med
    • 6.7.8. bgp client-to-client reflection
    • 6.7.9. bgp cluster-id
    • 6.7.10. bgp confederation identifier
    • 6.7.11. bgp confederation peers
    • 6.7.12. bgp dampening
    • 6.7.13. bgp default ipv4-unicast
    • 6.7.14. bgp default local-preference
    • 6.7.15. bgp deterministic-med
    • 6.7.16. bgp enforce-first-as
    • 6.7.17. bgp fast-external-failover
    • 6.7.18. bgp log-neighbor-changes
    • 6.7.19. bgp router-id
    • 6.7.20. bgp scan-time
    • 6.7.21. clear ip bgp *
    • 6.7.22. clear ip bgp A.B.C.D
    • 6.7.23. clear ip bgp dampening
    • 6.7.24. clear ip bgp flap-statistics
    • 6.7.25. clear ip bgp ASN
    • 6.7.26. clear ip bgp external
    • 6.7.27. clear ip bgp peer-group
    • 6.7.28. clear ip bgp vrf
    • 6.7.29. debug bgp
    • 6.7.30. distance
    • 6.7.31. exit-address-family
    • 6.7.32. ip as-path access-list
    • 6.7.33. ip community-list
    • 6.7.34. ip community-list expanded
    • 6.7.35. ip community-list standard
    • 6.7.36. neighbor activate
    • 6.7.37. neighbor advertisement-interval
    • 6.7.38. neighbor as-origination-interval
    • 6.7.39. neighbor allowas-in
    • 6.7.40. neighbor attribute-unchanged
    • 6.7.41. neighbor capability orf prefix-list
    • 6.7.42. neighbor capability route-refresh
    • 6.7.43. neighbor default-originate
    • 6.7.44. neighbor description
    • 6.7.45. neighbor distribute-list
    • 6.7.46. neighbor ebgp-multihop
    • 6.7.47. neighbor filter-list
    • 6.7.48. neighbor maximum-prefix
    • 6.7.49. neighbor next-hop-self
    • 6.7.50. neighbor override-capability
    • 6.7.51. neighbor passive
    • 6.7.52. neighbor peer-group (adding a neighbor)
    • 6.7.53. neighbor peer-group (creating a peer-group)
    • 6.7.54. neighbor prefix-list
    • 6.7.55. neighbor remote-as
    • 6.7.56. neighbor remove-private-AS
    • 6.7.57. neighbor route-reflector-client
    • 6.7.58. neighbor send-community
    • 6.7.59. neighbor shutdown
    • 6.7.60. neighbor soft-reconfiguration inbound
    • 6.7.61. neighbor strict-capability-match
    • 6.7.62. neighbor timers
    • 6.7.63. neighbor unsuppress-map
    • 6.7.64. neighbor update-source
    • 6.7.65. neighbor weight
    • 6.7.66. neighbor fall-over bfd
    • 6.7.67. network
    • 6.7.68. network synchronization
    • 6.7.69. synchronization
    • 6.7.70. router bgp
    • 6.7.71. show debugging bgp
    • 6.7.72. show ip bgp
    • 6.7.73. show ip bgp attribute-info
    • 6.7.74. show ip bgp cidr-only
    • 6.7.75. show ip bgp community
    • 6.7.76. show ip bgp community-info
    • 6.7.77. show ip bgp community-list
    • 6.7.78. show ip bgp dampening
    • 6.7.79. show ip bgp filter-list
    • 6.7.80. show ip bgp inconsistent-as
    • 6.7.81. show ip bgp neighbors
    • 6.7.82. show ip bgp paths
    • 6.7.83. show ip bgp prefix-list
    • 6.7.84. show ip bgp quote-regexp
    • 6.7.85. show ip bgp regexp
    • 6.7.86. show ip bgp scan
    • 6.7.87. show ip bgp summary
    • 6.7.88. show ip bgp vpnv4 all
    • 6.7.89. show ip bgp vpnv4 rd
    • 6.7.90. show ip bgp vpnv4 vrf
    • 6.7.91. timers
    • 6.7.92. max-paths
  • 6.8. ISIS Commands
    • 6.8.1. accept-lifetime
    • 6.8.2. address-family ipv6
    • 6.8.3. adjacency-check
    • 6.8.4. area-password
    • 6.8.5. authentication key-chain
    • 6.8.6. authentication mode md5
    • 6.8.7. authentication send-only
    • 6.8.8. bfd all-interfaces
    • 6.8.9. clear clns neighbors
    • 6.8.10. clear clns is-neighbors
    • 6.8.11. clear ip isis route
    • 6.8.12. clear isis counter
    • 6.8.13. clear isis interface counter
    • 6.8.14. clear isis process
    • 6.8.15. debug isis
    • 6.8.16. default-information originate
    • 6.8.17. distance
    • 6.8.18. domain-password
    • 6.8.19. ignore-lsp-errors
    • 6.8.20. ip route high-priority tag
    • 6.8.21. ip router isis
    • 6.8.22. ipv6 router isis
    • 6.8.23. isis authentication key-chain
    • 6.8.24. isis authentication mode md5
    • 6.8.25. isis authentication send-only
    • 6.8.26. isis bfd
    • 6.8.27. isis circuit-type
    • 6.8.28. isis csnp-interval
    • 6.8.29. isis hello
    • 6.8.30. isis hello-interval
    • 6.8.31. isis hello-multiplier
    • 6.8.32. isis lsp-interval
    • 6.8.33. isis mesh-group
    • 6.8.34. isis metric
    • 6.8.35. isis network
    • 6.8.36. isis password
    • 6.8.37. isis priority
    • 6.8.38. isis retransmit-interval
    • 6.8.39. isis tag
    • 6.8.40. ispf
    • 6.8.41. is-type
    • 6.8.42. lsp-gen-interval
    • 6.8.43. lsp-mtu
    • 6.8.44. lsp-refresh-interval
    • 6.8.45. max-area-addresses
    • 6.8.46. max-lsp-lifetime
    • 6.8.47. metric-style
    • 6.8.48. net
    • 6.8.49. passive-interface
    • 6.8.50. prc-interval-exp
    • 6.8.51. redistribute
    • 6.8.52. redistribute isis
    • 6.8.53. router isis
    • 6.8.54. set-overload-bit
    • 6.8.55. spf-interval-exp
    • 6.8.56. summary-address
    • 6.8.57. summary-prefix
    • 6.8.58. show clns is-neighbors
    • 6.8.59. show debugging isis
    • 6.8.60. show ip isis route
    • 6.8.61. show ipv6 isis route
    • 6.8.62. show ipv6 isis topology
    • 6.8.63. show ipv6 protocols isis
    • 6.8.64. show isis counter
    • 6.8.65. show isis database
    • 6.8.66. show isis interface
    • 6.8.67. show isis topology
    • 6.8.68. show running-config interface isis
    • 6.8.69. show running-config router isis
• 7. IPv6 Routing Commands
  • 7.1. OSPFv3 Commands
    • 7.1.1. area default-cost
    • 7.1.2. area range
    • 7.1.3. area stub
    • 7.1.4. auto-cost
    • 7.1.5. clear ipv6 ospf
    • 7.1.6. default-information originate (OSPFv3)
    • 7.1.7. default-metric (OSPFv3)
    • 7.1.8. distance (OSPFv3)
    • 7.1.9. distribute-list (OSPFv3)
    • 7.1.10. enable db-summary-opt
    • 7.1.11. ipv6 ospf cost
    • 7.1.12. ipv6 ospf dead-interval
    • 7.1.13. ipv6 ospf hello-interval
    • 7.1.14. ipv6 ospf mtu-ignore
    • 7.1.15. ipv6 ospf priority
    • 7.1.16. ipv6 ospf retransmit-interval
    • 7.1.17. ipv6 ospf transmit-delay
    • 7.1.18. ipv6 ospf network
    • 7.1.19. ipv6 ospf neighbor
    • 7.1.20. passive-interface (OSPF)
    • 7.1.21. redistribute (OSPFv3)
    • 7.1.22. router-id (OSPF)
    • 7.1.23. router ipv6 ospf
    • 7.1.24. summary-address (OSPFv3)
    • 7.1.25. show ipv6 ospf
    • 7.1.26. show ipv6 ospf database
    • 7.1.27. show ipv6 ospf interface
    • 7.1.28. show ipv6 ospf neighbor
    • 7.1.29. show ipv6 ospf database database-summary
    • 7.1.30. show ipv6 ospf route
    • 7.1.31. show ipv6 ospf route summary
    • 7.1.32. show ipv6 protocols ospf
    • 7.1.33. timers spf
    • 7.1.34. max-concurrent-dd
    • 7.1.35. debug ipv6 ospf
    • 7.1.36. debug ipv6 ospf events
    • 7.1.37. debug ipv6 ospf ifsm
    • 7.1.38. debug ipv6 ospf nfsm
    • 7.1.39. debug ipv6 ospf lsa
    • 7.1.40. debug ipv6 ospf packet
    • 7.1.41. debug ipv6 ospf route
    • 7.1.42. show debugging ipv6 ospf
    • 7.1.43. show resource ipv6 ospf
    • 7.1.44. show ipv6 vrf ospf
    • 7.1.45. area nssa
  • 7.2. RIPng Commands
    • 7.2.1. router ipv6 rip
    • 7.2.2. ipv6 router rip
    • 7.2.3. ipv6 rip metric-offset
    • 7.2.4. ipv6 rip split-horizon
    • 7.2.5. default-information originate (RIPng)
    • 7.2.6. default-metric (RIPng)
    • 7.2.7. distance (RIPng)
    • 7.2.8. neighbor (RIPng)
    • 7.2.9. offset-list (RIPng)
    • 7.2.10. passive-interface (RIPng)
    • 7.2.11. redistribute (RIPng)
    • 7.2.12. timers basic (RIPng)
    • 7.2.13. distribute-list(RIPng)
    • 7.2.14. aggregate-address (RIPng)
    • 7.2.15. route map(RIPng)
    • 7.2.16. maximum-prefix(RIPng)
    • 7.2.17. show ipv6 rip database
    • 7.2.18. show ipv6 rip interface
    • 7.2.19. show ipv6 rip database database-summary
    • 7.2.20. show ipv6 protocol rip
    • 7.2.21. debug ipv6 rip
    • 7.2.22. show debugging ipv6 rip
    • 7.2.23. show resource ipv6 rip
    • 7.2.24. clear ipv6 rip route
  • 7.3. IPv6UC Commands
    • 7.3.1. ipv6 enable
    • 7.3.2. max-static-v6routes
    • 7.3.3. ipv6 route
    • 7.3.4. ipv6 address
    • 7.3.5. show ipv6 route
    • 7.3.6. show ipv6 interface
    • 7.3.7. ipv6 verify unicast reverse-path
    • 7.3.8. ipv6 icmp error-interval
    • 7.3.9. clear ipv6 route static
  • 7.4. Ipv6 Prefix-list Commands
    • 7.4.1. ipv6 prefix-list
    • 7.4.2. ipv6 prefix-list description
    • 7.4.3. ipv6 prefix-list sequence-number
    • 7.4.4. show ipv6 prefix-list
    • 7.4.5. clear ipv6 prefix-list
  • 7.5. Route Map Commands
    • 7.5.1. route-map
    • 7.5.2. match as-path
    • 7.5.3. match community
    • 7.5.4. match interface
    • 7.5.5. match ipv6 address
    • 7.5.6. match ipv6 address prefix-list
    • 7.5.7. match ipv6 next-hop
    • 7.5.8. match ipv6 next-hop prefix-list
    • 7.5.9. match local-preference
    • 7.5.10. match metric
    • 7.5.11. match origin
    • 7.5.12. match route-type
    • 7.5.13. match tag
    • 7.5.14. set ipv6 aggregator
    • 7.5.15. set as-path
    • 7.5.16. set atomic-aggregate
    • 7.5.17. set comm-list delete
    • 7.5.18. set community
    • 7.5.19. set dampening
    • 7.5.20. set extcommunity
    • 7.5.21. set ipv6 next-hop
    • 7.5.22. set local-preference
    • 7.5.23. set metric
    • 7.5.24. set metric-type
    • 7.5.25. set origin
    • 7.5.26. set ipv6 originator-id
    • 7.5.27. set tag
    • 7.5.28. set vpnv6 next-hop
    • 7.5.29. set weight
    • 7.5.30. show route-map
  • 7.6. IPv6 BGP Commands
    • 7.6.1. address-family
    • 7.6.2. aggregate-address
    • 7.6.3. bgp always-compare-med
    • 7.6.4. bgp bestpath as-path ignore
    • 7.6.5. bgp bestpath compare-confed-aspath
    • 7.6.6. bgp bestpath compare-routerid
    • 7.6.7. bgp bestpath med
    • 7.6.8. bgp client-to-client reflection
    • 7.6.9. bgp cluster-id
    • 7.6.10. bgp confederation identifier
    • 7.6.11. bgp confederation peers
    • 7.6.12. bgp dampening
    • 7.6.13. bgp default local-preference
    • 7.6.14. bgp deterministic-med
    • 7.6.15. bgp enforce-first-as
    • 7.6.16. bgp fast-external-failover
    • 7.6.17. bgp log-neighbor-changes
    • 7.6.18. bgp router-id
    • 7.6.19. bgp scan-time
    • 7.6.20. clear bgp ipv6 *
    • 7.6.21. clear bgp ipv6 X:X::X:X
    • 7.6.22. clear bgp ipv6 unicast dampening
    • 7.6.23. clear bgp ipv6 unicast flap-statistics
    • 7.6.24. clear bgp ipv6 ASN
    • 7.6.25. clear bgp ipv6 external
    • 7.6.26. clear bgp ipv6 peer-group
    • 7.6.27. debug bgp
    • 7.6.28. exit-address-family
    • 7.6.29. neighbor activate
    • 7.6.30. neighbor advertisement-interval
    • 7.6.31. neighbor allowas-in
    • 7.6.32. neighbor attribute-unchanged
    • 7.6.33. neighbor capability graceful-restart
    • 7.6.34. neighbor capability orf prefix-list
    • 7.6.35. neighbor default-originate
    • 7.6.36. neighbor description
    • 7.6.37. neighbor distribute-list
    • 7.6.38. neighbor ebgp-multihop
    • 7.6.39. neighbor filter-list
    • 7.6.40. neighbor maximum-prefix
    • 7.6.41. neighbor next-hop-self
    • 7.6.42. neighbor override-capability
    • 7.6.43. neighbor passive
    • 7.6.44. neighbor peer-group (adding a neighbor)
    • 7.6.45. neighbor peer-group (creating a peer-group)
    • 7.6.46. neighbor prefix-list
    • 7.6.47. neighbor remote-as
    • 7.6.48. neighbor remove-private-AS
    • 7.6.49. neighbor route-reflector-client
    • 7.6.50. neighbor send-community
    • 7.6.51. neighbor shutdown
    • 7.6.52. neighbor soft-reconfiguration inbound
    • 7.6.53. neighbor strict-capability-match
    • 7.6.54. neighbor timers
    • 7.6.55. neighbor unsuppress-map
    • 7.6.56. neighbor update-source
    • 7.6.57. neighbor weight
    • 7.6.58. network
    • 7.6.59. network synchronization
    • 7.6.60. synchronization
    • 7.6.61. router bgp
    • 7.6.62. show debugging bgp
    • 7.6.63. show bgp ipv6
    • 7.6.64. show bgp ipv6 community
    • 7.6.65. show bgp ipv6 community-list
    • 7.6.66. show bgp ipv6 dampening
    • 7.6.67. show bgp ipv6 filter-list
    • 7.6.68. show bgp ipv6 inconsistent-as
    • 7.6.69. show bgp ipv6 neighbors
    • 7.6.70. show bgp ipv6 paths
    • 7.6.71. show bgp ipv6 prefix-list
    • 7.6.72. show bgp ipv6 quote-regexp
    • 7.6.73. show bgp ipv6 regexp
    • 7.6.74. show bgp ipv6 summary
    • 7.6.75. timers
    • 7.6.76. neighbor fall-over bfd
• 8. Multicast Commands
  • 8.1. IP Multicast-Routing Commands
    • 8.1.1. ip multicast-routing
    • 8.1.2. ip multicast route-limit
    • 8.1.3. show ip mroute
    • 8.1.4. show ip mvif
    • 8.1.5. show ip multicast groups count
    • 8.1.6. show resource mcast
    • 8.1.7. clear ip mroute
  • 8.2. IGMP Commands
    • 8.2.1. ip igmp access-group
    • 8.2.2. ip igmp immediate-leave group-list
    • 8.2.3. ip igmp last-member-query-count
    • 8.2.4. ip igmp last-member-query-interval
    • 8.2.5. ip igmp limit
    • 8.2.6. ip igmp mroute-proxy
    • 8.2.7. ip igmp proxy-service
    • 8.2.8. ip igmp querier-timeout
    • 8.2.9. ip igmp query-interval
    • 8.2.10. ip igmp query-max-response-time
    • 8.2.11. ip igmp robustness-variable
    • 8.2.12. ip igmp version
    • 8.2.13. ip igmp static-group
    • 8.2.14. ip igmp ssm-map enable
    • 8.2.15. ip igmp ssm-map static
    • 8.2.16. clear ip igmp
    • 8.2.17. clear ip igmp interface
    • 8.2.18. show ip igmp groups
    • 8.2.19. show ip igmp groups interface
    • 8.2.20. show ip igmp groups count
    • 8.2.21. show ip igmp interface
  • 8.3. IGMP Snooping Commands
    • 8.3.1. ip igmp snooping
    • 8.3.2. ip igmp snooping fast-leave
    • 8.3.3. ip igmp snooping last-member-query-interval
    • 8.3.4. ip igmp snooping global source-address
    • 8.3.5. ip igmp snooping max-member-num
    • 8.3.6. ip igmp snooping query-interval
    • 8.3.7. ip igmp snooping query-max-response-time
    • 8.3.8. ip igmp snooping report-suppression
    • 8.3.9. ip igmp snooping version
    • 8.3.10. ip igmp snooping discard-unknown
    • 8.3.11. ip igmp snooping querier tcn
    • 8.3.12. ip igmp snooping vlan access-group
    • 8.3.13. ip igmp snooping vlan mrouter interface
    • 8.3.14. ip igmp snooping vlan mrouter-aging-interval
    • 8.3.15. ip igmp snooping vlan mrouter-port-discard
    • 8.3.16. ip igmp snooping vlan querier
    • 8.3.17. ip igmp snooping vlan querier address
    • 8.3.18. ip igmp snooping vlan querier-timeout
    • 8.3.19. ip igmp snooping vlan static-group
    • 8.3.20. ip igmp snooping vlan static-group remote-vtep
    • 8.3.21. clear ip igmp snooping group
    • 8.3.22. clear ip igmp snooping vlan
    • 8.3.23. clear ip igmp snooping mrouter vlan
    • 8.3.24. clear ip igmp snooping mrouter
    • 8.3.25. show ip igmp snooping global
    • 8.3.26. show ip igmp snooping groups
    • 8.3.27. show ip igmp snooping groups vlan
    • 8.3.28. show ip igmp snooping groups count
    • 8.3.29. show ip igmp snooping querier
    • 8.3.30. show ip igmp snooping mrouter
    • 8.3.31. show ip igmp snooping vlan
    • 8.3.32. show resource l2mcast
  • 8.4. PIM Commands
    • 8.4.1. ip pim accept-register
    • 8.4.2. ip pim anycast-rp
    • 8.4.3. ip pim bsr-candidate
    • 8.4.4. ip pim bsr-border
    • 8.4.5. ip pim dr-priority
    • 8.4.6. ip pim exclude-genid
    • 8.4.7. ip pim hello-interval
    • 8.4.8. ip pim ignore-rp-set-priority
    • 8.4.9. ip pim jp-timer
    • 8.4.10. ip pim neighbor-filter
    • 8.4.11. ip pim register-rate-limit
    • 8.4.12. ip pim register-source
    • 8.4.13. ip pim register-rp-reachability
    • 8.4.14. ip pim register-suppression
    • 8.4.15. ip pim rp-address
    • 8.4.16. ip pim rp-candidate
    • 8.4.17. ip pim rp-register-kat
    • 8.4.18. ip pim spt-switch-threshold infinity
    • 8.4.19. ip pim cisco-register-checksum
    • 8.4.20. ip pim sparse-mode
    • 8.4.21. ip pim dense-mode
    • 8.4.22. ip pim propagation-delay
    • 8.4.23. ip pim state-refresh origination-interval
    • 8.4.24. ip pim unicast-bsm
    • 8.4.25. ip pim ssm
    • 8.4.26. ip pim graceful-restart
    • 8.4.27. show ip pim sparse-mode bsr-router
    • 8.4.28. show ip pim sparse-mode interface
    • 8.4.29. show ip pim sparse-mode local-member
    • 8.4.30. show ip pim sparse-mode mroute
    • 8.4.31. show ip pim sparse-mode neighbor
    • 8.4.32. show ip pim sparse-mode rp mapping
    • 8.4.33. show ip pim sparse-mode rp-hash
    • 8.4.34. show ip pim sparse-mode spt-threshold
    • 8.4.35. show ip pim dense-mode interface
    • 8.4.36. show ip pim dense-mode mroute
    • 8.4.37. show ip pim dense-mode neighbor
    • 8.4.38. show ip pim dense-mode nexthop
    • 8.4.39. show ip pim dense-mode interface
    • 8.4.40. show ip pim dense-mode mroute
    • 8.4.41. show ip pim sparse-mode nexthop-virtual-pair
    • 8.4.42. ip pim nexthop-address
    • 8.4.43. show ip pim graceful-restart
  • 8.5. MVR Commands
    • 8.5.1. mvr
    • 8.5.2. mvr vlan
    • 8.5.3. mvr group
    • 8.5.4. mvr source-address
    • 8.5.5. mvr type
    • 8.5.6. show mvr
    • 8.5.7. show mvr interface
    • 8.5.8. show mvr group
    • 8.5.9. show mvr group static
    • 8.5.10. show resource mvr
• 9. IPv6 Multicast Commands
  • 9.1. IPv6 Multicast-Routing Commands
    • 9.1.1. Ipv6 multicast-routing
    • 9.1.2. ipv6 multicast route-limit
    • 9.1.3. show ipv6 mroute
    • 9.1.4. show ipv6 mif
    • 9.1.5. show ipv6 multicast groups count
    • 9.1.6. show resource mcast6
    • 9.1.7. clear ipv6 mroute
  • 9.2. MLD Commands
    • 9.2.1. ipv6 mld access-group
    • 9.2.2. ipv6 mld last-member-query-count
    • 9.2.3. ipv6 mld last-member-query-interval
    • 9.2.4. ipv6 mld limit
    • 9.2.5. ipv6 mld mroute-proxy
    • 9.2.6. ipv6 mld proxy-service
    • 9.2.7. ipv6 mld querier-timeout
    • 9.2.8. ipv6 mld query-interval
    • 9.2.9. ipv6 mld query-max-response-time
    • 9.2.10. ipv6 mld robustness-variable
    • 9.2.11. ipv6 mld version
    • 9.2.12. ipv6 mld static-group
    • 9.2.13. ipv6 mld ssm-map enable
    • 9.2.14. ipv6 mld ssm-map static
    • 9.2.15. clear ipv6 mld
    • 9.2.16. clear ipv6 mld interface
    • 9.2.17. show ipv6 mld groups
    • 9.2.18. show ipv6 mld groups interface
    • 9.2.19. show ipv6 mld groups count
    • 9.2.20. show ipv6 mld interface
  • 9.3. MLD Snooping Commands
    • 9.3.1. ipv6 mld snooping
    • 9.3.2. ipv6 mld snooping fast-leave
    • 9.3.3. ipv6 mld snooping last-member-query-interval
    • 9.3.4. ipv6 mld snooping global source-address
    • 9.3.5. ipv6 mld snooping max-member-num
    • 9.3.6. ipv6 mld snooping query-interval
    • 9.3.7. ipv6 mld snooping query-max-response-time
    • 9.3.8. ipv6 mld snooping report-suppression
    • 9.3.9. ipv6 mld snooping version
    • 9.3.10. ipv6 mld snooping discard-unknown
    • 9.3.11. ipv6 mld snooping querier tcn
    • 9.3.12. ipv6 mld snooping vlan access-group
    • 9.3.13. ipv6 mld snooping vlan mrouter interface
    • 9.3.14. ipv6 mld snooping vlan mrouter-aging-interval
    • 9.3.15. ipv6 mld snooping vlan querier
    • 9.3.16. ipv6 mld snooping vlan querier address
    • 9.3.17. ipv6 mld snooping vlan querier-timeout
    • 9.3.18. ipv6 mld snooping vlan static-group
    • 9.3.19. clear ipv6 mld snooping group
    • 9.3.20. clear ipv6 mld snooping vlan group
    • 9.3.21. show ipv6 mld snooping global
    • 9.3.22. show ipv6 mld snooping groups
    • 9.3.23. show ipv6 mld snooping groups vlan
    • 9.3.24. show ipv6 mld snooping groups count
    • 9.3.25. show ipv6 mld snooping querier
    • 9.3.26. show ipv6 mld snooping mrouter
    • 9.3.27. show ipv6 mld snooping vlan
    • 9.3.28. show resource l2mcast
  • 9.4. PIMv6 Commands
    • 9.4.1. ipv6 pim accept-register
    • 9.4.2. ipv6 pim anycast-rp
    • 9.4.3. ipv6 pim bsr-candidate
    • 9.4.4. ipv6 pim bsr-border
    • 9.4.5. ipv6 pim dr-priority
    • 9.4.6. ipv6 pim exclude-genid
    • 9.4.7. ipv6 pim hello-interval
    • 9.4.8. ipv6 pim ignore-rp-set-priority
    • 9.4.9. ipv6 pim jp-timer
    • 9.4.10. ipv6 pim neighbor-filter
    • 9.4.11. ipv6 pim register-rate-limit
    • 9.4.12. ipv6 pim register-source
    • 9.4.13. ipv6 pim register-rp-reachability
    • 9.4.14. ipv6 pim register-suppression
    • 9.4.15. ipv6 pim rp-address
    • 9.4.16. ipv6 pim rp-candidate
    • 9.4.17. ipv6 pim rp-register-kat
    • 9.4.18. ipv6 pim spt-switch-threshold infinity
    • 9.4.19. ipv6 pim cisco-register-checksum
    • 9.4.20. ipv6 pim sparse-mode
    • 9.4.21. ipv6 pim unicast-bsm
    • 9.4.22. ipv6 pim ssm
    • 9.4.23. show ipv6 pim sparse-mode bsr-router
    • 9.4.24. show ipv6 pim sparse-mode interface
    • 9.4.25. show ipv6 pim sparse-mode local-member
    • 9.4.26. show ipv6 pim sparse-mode mroute
    • 9.4.27. show ipv6 pim sparse-mode neighbor
    • 9.4.28. show ipv6 pim sparse-mode rp mapping
    • 9.4.29. show ipv6 pim sparse-mode rp-hash
    • 9.4.30. show ipv6 pim sparse-mode spt-threshold
  • 9.5. MVR6 Commands
    • 9.5.1. mvr6
    • 9.5.2. mvr6 vlan
    • 9.5.3. mvr6 group
    • 9.5.4. mvr6 source-address
    • 9.5.5. mvr6 type
    • 9.5.6. show mvr6
    • 9.5.7. show mvr6 interface
    • 9.5.8. show mvr6 group
    • 9.5.9. show mvr6 group static
    • 9.5.10. show resource mvr6
• 10. Traffic Management Commands (QoS)
  • 10.1. QOS Commands
    • 10.1.1. table-map
    • 10.1.2. map
    • 10.1.3. default
    • 10.1.4. class-map type qos
    • 10.1.5. match access-group
    • 10.1.6. match cos
    • 10.1.7. match dscp
    • 10.1.8. class-map type traffic-class
    • 10.1.9. match traffic-class
    • 10.1.10. policy-map type qos
    • 10.1.11. class type qos
    • 10.1.12. class type qos class-default
    • 10.1.13. set cos
    • 10.1.14. set dscp
    • 10.1.15. set traffic-class
    • 10.1.16. set color
    • 10.1.17. policer
    • 10.1.18. qos aggregate-policer
    • 10.1.19. aggregate-policer
    • 10.1.20. policy-map type traffic-class
    • 10.1.21. class type traffic-class
    • 10.1.22. class type traffic-class class-default
    • 10.1.23. priority level
    • 10.1.24. bandwidth percentage
    • 10.1.25. queue-limit
    • 10.1.26. queue-limit dynamic
    • 10.1.27. random-detect
    • 10.1.28. service-policy type qos
    • 10.1.29. service-policy type traffic-class
    • 10.1.30. qos policer
    • 10.1.31. qos shape rate
    • 10.1.32. show table-map
    • 10.1.33. show class-map
    • 10.1.34. show policy-map
    • 10.1.35. show qos aggregate-policer
    • 10.1.36. show qos interface ingress
    • 10.1.37. show qos interface egress
    • 10.1.38. show qos aggregate-policer statistics
    • 10.1.39. show policy-map type qos statistics interface ace
    • 10.1.40. show policy-map type qos statistics vlan ace
    • 10.1.41. show policy-map type qos statistics port-group ace
    • 10.1.42. show policy-map type qos statistics vlan-group ace
    • 10.1.43. show policy-map type qos statistics interface policer
    • 10.1.44. show policy-map type qos statistics vlan policer
    • 10.1.45. show policy-map type qos statistics port-group policer
    • 10.1.46. show policy-map type qos statistics vlan-group policer
    • 10.1.47. show qos interface statistics policer
    • 10.1.48. show qos interface statistics queue
    • 10.1.49. clear qos aggregate-policer statistics
    • 10.1.50. clear policy-map type qos statistics interface ace
    • 10.1.51. clear policy-map type qos statistics vlan ace
    • 10.1.52. clear policy-map type qos statistics port-group ace
    • 10.1.53. clear policy-map type qos statistics vlan-group ace
    • 10.1.54. clear policy-map type qos statistics ace
    • 10.1.55. clear policy-map type qos statistics interface policer
    • 10.1.56. clear policy-map type qos statistics vlan policer
    • 10.1.57. clear policy-map type qos statistics port-group policer
    • 10.1.58. clear policy-map type qos statistics vlan-group policer
    • 10.1.59. clear policy-map type qos statistics policer
    • 10.1.60. clear qos interface statistics policer
    • 10.1.61. clear qos vlan statistics policer
    • 10.1.62. clear qos interface statistics queue
    • 10.1.63. flow-policer number
    • 10.1.64. ipg shaping enable
    • 10.1.65. ipg policer enable
    • 10.1.66. smart buffer enable
    • 10.1.67. service-policy
    • 10.1.68. access-group
    • 10.1.69. trust
• 11. Security Commands
  • 11.1. Port Security Commands
    • 11.1.1. clear port-security address-table static
    • 11.1.2. switchport port-security
    • 11.1.3. switchport port-security mac-address
    • 11.1.4. switchport port-security maximum
    • 11.1.5. switchport port-security violation
    • 11.1.6. show port-security address-table
    • 11.1.7. show port-security current mac-num interface
    • 11.1.8. show port-security interface
    • 11.1.9. show port-security maximum mac-num interface
  • 11.2. Vlan Security Commands
    • 11.2.1. vlan mac-limit maximum
    • 11.2.2. vlan mac-limit action
    • 11.2.3. vlan mac learning
    • 11.2.4. show vlan-security
  • 11.3. Time Range Commands
    • 11.3.1. time-range
    • 11.3.2. absolute
    • 11.3.3. periodic
    • 11.3.4. show time-range
  • 11.4. ACL Commands
    • 11.4.1. mac access-list
    • 11.4.2. sequence-num
    • 11.4.3. deny src-mac
    • 11.4.4. permit src-mac
    • 11.4.5. remark
    • 11.4.6. show access-list mac
    • 11.4.7. ip access-list
    • 11.4.8. deny
    • 11.4.9. deny tcp
    • 11.4.10. deny udp
    • 11.4.11. deny icmp
    • 11.4.12. deny igmp
    • 11.4.13. deny gre
    • 11.4.14. deny nvgre
    • 11.4.15. permit
    • 11.4.16. permit tcp
    • 11.4.17. permit udp
    • 11.4.18. permit icmp
    • 11.4.19. permit igmp
    • 11.4.20. permit gre
    • 11.4.21. permit nvgre
    • 11.4.22. show access-list ip
    • 11.4.23. udf access-list
    • 11.4.24. permit udf
    • 11.4.25. deny udf
    • 11.4.26. show access-list udf
  • 11.5. FLEX ACL Commands
    • 11.5.1. sequence-num
    • 11.5.2. deny src-mac
    • 11.5.3. permit src-mac
    • 11.5.4. remark
    • 11.5.5. ip access-list
    • 11.5.6. sequence-num
    • 11.5.7. deny src-mac
    • 11.5.8. permit src-mac
    • 11.5.9. deny
    • 11.5.10. deny tcp
    • 11.5.11. deny udp
    • 11.5.12. deny icmp
    • 11.5.13. deny igmp
    • 11.5.14. deny gre
    • 11.5.15. deny nvgre
    • 11.5.16. permit
    • 11.5.17. permit tcp
    • 11.5.18. permit udp
    • 11.5.19. permit icmp
    • 11.5.20. permit igmp
    • 11.5.21. permit gre
    • 11.5.22. permit nvgre
    • 11.5.23. remark
    • 11.5.24. sequence-num
    • 11.5.25. remark
    • 11.5.26. show access-list mpls
    • 11.5.27. deny
    • 11.5.28. permit
  • 11.6. Extend ACL Commands
    • 11.6.1. ip access-list extend
    • 11.6.2. sequence-num
    • 11.6.3. deny src-mac
    • 11.6.4. permit src-mac
    • 11.6.5. deny
    • 11.6.6. deny tcp
    • 11.6.7. deny udp
    • 11.6.8. deny icmp
    • 11.6.9. deny igmp
    • 11.6.10. deny gre
    • 11.6.11. deny nvgre
    • 11.6.12. permit
    • 11.6.13. permit tcp
    • 11.6.14. permit udp
    • 11.6.15. permit icmp
    • 11.6.16. permit igmp
    • 11.6.17. permit gre
    • 11.6.18. permit nvgre
    • 11.6.19. remark
    • 11.6.20. show access-list ip extend
  • 11.7. ACLv6 Commands
    • 11.7.1. ipv6 access-list
    • 11.7.2. sequence-num
    • 11.7.3. remark
    • 11.7.4. deny
    • 11.7.5. deny tcp
    • 11.7.6. deny udp
    • 11.7.7. deny icmp
    • 11.7.8. deny gre
    • 11.7.9. deny nvgre
    • 11.7.10. permit
    • 11.7.11. permit tcp
    • 11.7.12. permit udp
    • 11.7.13. permit icmp
    • 11.7.14. permit gre
    • 11.7.15. permit nvgre
    • 11.7.16. show access-list ipv6
  • 11.8. FLEX ACLv6 Commands
    • 11.8.1. sequence-num
    • 11.8.2. remark
    • 11.8.3. deny
    • 11.8.4. deny tcp
    • 11.8.5. deny udp
    • 11.8.6. deny icmp
    • 11.8.7. deny gre
    • 11.8.8. deny nvgre
    • 11.8.9. permit
    • 11.8.10. permit tcp
    • 11.8.11. permit udp
    • 11.8.12. permit icmp
    • 11.8.13. permit gre
    • 11.8.14. permit nvgre
  • 11.9. Port Group Commands
    • 11.9.1. port-group
    • 11.9.2. member interface
  • 11.10. Vlan Group Commands
    • 11.10.1. vlan-group
    • 11.10.2. menber vlan
  • 11.11. COPP Commands
    • 11.11.1. control-plane access-list
    • 11.11.2. (deny|permit) exception any
    • 11.11.3. (deny|permit) exception ipda
    • 11.11.4. (deny|permit) exception fwd-to-cpu
    • 11.11.5. (deny|permit) exception slow-protocol
    • 11.11.6. (deny|permit) exception dhcp
    • 11.11.7. (deny|permit) exception rip
    • 11.11.8. (deny|permit) exception ospf
    • 11.11.9. (deny|permit) exception pim
    • 11.11.10. (deny|permit) exception bgp
    • 11.11.11. (deny|permit) exception vrrp
    • 11.11.12. (deny|permit) exception ssh
    • 11.11.13. (deny|permit) exception telnet
    • 11.11.14. (deny|permit) exception tcp
    • 11.11.15. (deny|permit) exception mlag
    • 11.11.16. (deny|permit) exception arp
    • 11.11.17. (deny|permit) exception igmp
    • 11.11.18. (deny|permit) exception
    • 11.11.19. class-map type (control-plane)
    • 11.11.20. policy-map type (control-plane)
    • 11.11.21. class type control-plane
    • 11.11.22. statistics enable
    • 11.11.23. control-plane
    • 11.11.24. service-policy type control-plane input
    • 11.11.25. show policy-map type control-plane statistics input ace
    • 11.11.26. policer cir
    • 11.11.27. show policy-map type control-plane statistics input policer
  • 11.12. FLEX COPP Commands
    • 11.12.1. control-plane access-list-template
    • 11.12.2. mac-field
    • 11.12.3. ip-field
    • 11.12.4. arp-field
    • 11.12.5. control-plane access-list template
    • 11.12.6. (deny|permit) exception any
    • 11.12.7. (deny|permit) exception any
    • 11.12.8. (deny|permit) exception ipda
    • 11.12.9. (deny|permit) exception fwd-to-cpu
    • 11.12.10. (deny|permit) exception slow-protocol
    • 11.12.11. (deny|permit) exception dhcp
    • 11.12.12. (deny|permit) exception rip
    • 11.12.13. (deny|permit) exception ospf
    • 11.12.14. (deny|permit) exception pim
    • 11.12.15. (deny|permit) exception bgp
    • 11.12.16. (deny|permit) exception vrrp
    • 11.12.17. (deny|permit) exception ssh
    • 11.12.18. (deny|permit) exception telnet
    • 11.12.19. (deny|permit) exception tcp
    • 11.12.20. (deny|permit) exception mlag
    • 11.12.21. (deny|permit) exception arp
    • 11.12.22. (deny|permit) exception igmp
    • 11.12.23. (deny|permit) exception
    • 11.12.24. class-map type (control-plane)
    • 11.12.25. match access-group
    • 11.12.26. policy-map type (control-plane)
    • 11.12.27. class type control-plane
    • 11.12.28. statistics enable
    • 11.12.29. control-plane
    • 11.12.30. service-policy type control-plane input
    • 11.12.31. show policy-map type control-plane statistics input ace
    • 11.12.32. policer cir
    • 11.12.33. show policy-map type control-plane statistics input policer
  • 11.13. IEEE 802.1x Commands
    • 11.13.1. dot1x system-auth-ctrl
    • 11.13.2. dot1x initialize
    • 11.13.3. dot1x max-req
    • 11.13.4. dot1x port-control
    • 11.13.5. dot1x protocol-version
    • 11.13.6. dot1x timeout quiet-period
    • 11.13.7. dot1x handshake
    • 11.13.8. dot1x timeout handshake-period
    • 11.13.9. dot1x reauthentication
    • 11.13.10. dot1x re-authenticate
    • 11.13.11. dot1x timeout
    • 11.13.12. dot1x guest-vlan
    • 11.13.13. show dot1x
    • 11.13.14. show dot1x statistics
    • 11.13.15. debug dot1x
    • 11.13.16. clear dot1x statistics
    • 11.13.17. dot1x port-mode
    • 11.13.18. dot1x max-user
    • 11.13.19. dot1x re-active radius-server
    • 11.13.20. dot1x accounting-mode radius
    • 11.13.21. dot1x accounting start-fail
    • 11.13.22. dot1x accounting realtime
    • 11.13.23. dot1x accounting interim-fail
  • 11.14. Arp Inspection Commands
    • 11.14.1. show ip arp inspection
    • 11.14.2. show ip arp inspection interfaces
    • 11.14.3. show ip arp inspection log
    • 11.14.4. show ip arp inspection statistics
    • 11.14.5. show ip arp inspection vlan
    • 11.14.6. show debugging arp inspection
    • 11.14.7. debug arp inspection
    • 11.14.8. ip arp inspection filter vlan
    • 11.14.9. ip arp inspection log-buffer entries
    • 11.14.10. ip arp inspection log-buffer logs interval
    • 11.14.11. ip arp inspection validate
    • 11.14.12. ip arp inspection vlan
    • 11.14.13. ip arp inspection vlan logging acl-macth
    • 11.14.14. ip arp inspection vlan logging dhcp-bindings
    • 11.14.15. clear ip arp inspection log-buffer
    • 11.14.16. clear ip arp inspection statistics
    • 11.14.17. ip arp inspection trust
    • 11.14.18. arp access-list
    • 11.14.19. ip mac
    • 11.14.20. no sequence-num
    • 11.14.21. show access-list arp
  • 11.15. DHCP Snooping Commands
    • 11.15.1. clear dhcp snooping
    • 11.15.2. dhcp snooping
    • 11.15.3. dhcp snooping binding
    • 11.15.4. dhcp snooping database
    • 11.15.5. dhcp snooping information option
    • 11.15.6. dhcp snooping information option allow-untrusted
    • 11.15.7. dhcp snooping information option allow-untrusted (interface)
    • 11.15.8. dhcp snooping trust
    • 11.15.9. dhcp snooping verify
    • 11.15.10. dhcp snooping vlan
    • 11.15.11. dhcp snooping vlan information option format-type circuit-id string
    • 11.15.12. dhcp snooping information option format remote-id
    • 11.15.13. dhcp snooping information option format remote-id(interface)
    • 11.15.14. debug dhcp snooping
    • 11.15.15. show dhcp snooping binding
    • 11.15.16. show dhcp snooping config
    • 11.15.17. show dhcp snooping statistics
    • 11.15.18. show dhcp snooping trusted-sources
  • 11.16. IP Source Guard Commands
    • 11.16.1. ip source binding
    • 11.16.2. ipv6 source binding
    • 11.16.3. no ip source binding entries
    • 11.16.4. ip source maximal binding
    • 11.16.5. ip verify source
    • 11.16.6. show ip source binding
  • 11.17. AAA Commands
    • 11.17.1. aaa new-model
    • 11.17.2. aaa authentication login
    • 11.17.3. aaa authorization exec
    • 11.17.4. aaa accounting exec
    • 11.17.5. aaa accounting commands
    • 11.17.6. aaa privilege mapping
    • 11.17.7. login authentication
    • 11.17.8. authorization exec
    • 11.17.9. accounting exec
    • 11.17.10. accounting commands
    • 11.17.11. show aaa method-lists authentication
    • 11.17.12. show aaa status
    • 11.17.13. show aaa privilege mapping
    • 11.17.14. login-security enable
    • 11.17.15. login-security max-fail-num
    • 11.17.16. login-security lock-duration
    • 11.17.17. show login-security
    • 11.17.18. clear login-security record
  • 11.18. RADIUS Authentication Commands
    • 11.18.1. radius-server deadtime
    • 11.18.2. radius-server host
    • 11.18.3. radius-server retransmit
    • 11.18.4. radius-server timeout
    • 11.18.5. radius-server key
    • 11.18.6. show dot1x radius-server status
    • 11.18.7. show radius-server
  • 11.19. Tacacs+ Commands
    • 11.19.1. tacacs-server host
    • 11.19.2. clear tacacs statistics
    • 11.19.3. show tacacs
  • 11.20. Port Isolate Commands
    • 11.20.1. port-isolate group
    • 11.20.2. port-isolate mode
    • 11.20.3. show port-isolate
    • 11.20.4. port-isolate am
  • 11.21. Private Vlan Commands
    • 11.21.1. switchport mode private-vlan
    • 11.21.2. switchport private-vlan
    • 11.21.3. show private-vlan
  • 11.22. DDOS Commands
    • 11.22.1. ip icmp intercept
    • 11.22.2. ip smurf intercept
    • 11.22.3. ip fraggle intercept
    • 11.22.4. ip udp intercept
    • 11.22.5. ip tcp intercept
    • 11.22.6. ip small-packet intercept
    • 11.22.7. ip maceq intercept
    • 11.22.8. ip ipeq intercept
    • 11.22.9. show ip-intercept config
    • 11.22.10. show ip-intercept statistics
    • 11.22.11. clear ip-intercept statistics
  • 11.23. Key Chain Commands
    • 11.23.1. key chain
    • 11.23.2. key
    • 11.23.3. key-string
    • 11.23.4. accept-lifetime
    • 11.23.5. send-lifetime
    • 11.23.6. show key chain
  • 11.24. Port-block Commands
    • 11.24.1. port-block
    • 11.24.2. show port-block
  • 11.25. Device management securiy Commands
    • 11.25.1. ip telnet server acl
    • 11.25.2. ip ssh server acl
    • 11.25.3. service password-encryption
    • 11.25.4. http server acl
    • 11.25.5. service rpc-api acl
• 12. IPv6 Security Commands
  • 12.1. DHCPv6 Snooping Commands
    • 12.1.1. clear dhcpv6 snooping bindings learning
    • 12.1.2. clear dhcpv6 snooping statistics
    • 12.1.3. dhcpv6 snooping
    • 12.1.4. dhcpv6 snooping binding
    • 12.1.5. dhcpv6 snooping database
    • 12.1.6. dhcpv6 snooping remote-id format
    • 12.1.7. dhcpv6 snooping remote-id option
    • 12.1.8. dhcpv6 snooping trust
    • 12.1.9. dhcpv6 snooping vlan
    • 12.1.10. debug dhcpv6 snooping
    • 12.1.11. show dhcpv6 snooping binding
    • 12.1.12. show dhcpv6 snooping config
    • 12.1.13. show dhcpv6 snooping trusted-sources
    • 12.1.14. show dhcpv6 snooping statistics
  • 12.2. Device management securiy Commands
    • 12.2.1. ipv6 telnet server acl
    • 12.2.2. ipv6 ssh server acl
• 13. Reliability Commands
  • 13.1. BHM Commands
    • 13.1.1. sysmon enable
    • 13.1.2. show sysmon
    • 13.1.3. heart-beat-monitor enable
    • 13.1.4. heart-beat-monitor reactivate
    • 13.1.5. show heart-beat-monitor
  • 13.2. EFM Commands
    • 13.2.1. ethernet oam enable
    • 13.2.2. ethernet oam mode
    • 13.2.3. ethernet oam min-rate
    • 13.2.4. ethernet oam max-rate
    • 13.2.5. ethernet oam link-monitor on
    • 13.2.6. ethernet oam link-monitor supported
    • 13.2.7. ethernet oam link-monitor frame
    • 13.2.8. ethernet oam link-monitor frame-seconds threshold
    • 13.2.9. ethernet oam link-monitor high threshold action
    • 13.2.10. ethernet oam remote-loopback
    • 13.2.11. ethernet oam remote-loopback start
    • 13.2.12. ethernet oam remote-loopback stop
    • 13.2.13. ethernet oam timeout
    • 13.2.14. ethernet oam remote-failure
    • 13.2.15. show ethernet oam discovery
    • 13.2.16. show Ethernet oam status
    • 13.2.17. show ethernet oam state-machine
    • 13.2.18. show ethernet oam statistics
  • 13.3. CFM Commands
    • 13.3.1. ethernet cfm enable
    • 13.3.2. ethernet cfm domain level
    • 13.3.3. service
    • 13.3.4. ethernet cfm mep
    • 13.3.5. ethernet cfm mep crosscheck mpid
    • 13.3.6. ethernet cfm mip
    • 13.3.7. ethernet cfm cc enable domain
    • 13.3.8. ethernet cfm cc domain priority
    • 13.3.9. ethernet cfm loopback
    • 13.3.10. ethernet cfm loopback mac
    • 13.3.11. ethernet cfm errors enable domain
    • 13.3.12. clear ethernet cfm errors
    • 13.3.13. ethernet cfm ais status enable
    • 13.3.14. ethernet cfm ais suppress alarm enable domain
    • 13.3.15. ethernet cfm server-ais status enable level
    • 13.3.16. show ethernet cfm domain
    • 13.3.17. show ethernet cfm maintenance-points
    • 13.3.18. show ethernet cfm maintenance-points local
    • 13.3.19. show ethernet cfm maintenance-points remote
    • 13.3.20. show ethernet cfm cc config
    • 13.3.21. show ethernet cfm errors
    • 13.3.22. show ethernet cfm ais mep
    • 13.3.23. show ethernet cfm
    • 13.3.24. ethernet cfm linktrace rmepid
    • 13.3.25. ethernet cfm linktrace mac
    • 13.3.26. ethernet cfm linktrace cache enable
    • 13.3.27. ethernet cfm linktrace cache size
    • 13.3.28. ethernet cfm linktrace cache holdtime
    • 13.3.29. show ethernet cfm linktrace cache
    • 13.3.30. clear ethernet cfm linktrace cache
    • 13.3.31. ethernet cfm mip ccm-database size
    • 13.3.32. ethernet cfm mip ccm-database holdtime
    • 13.3.33. show ethernet cfm mip ccm-database
    • 13.3.34. clear ethernet cfm mip ccm-database
    • 13.3.35. ethernet cfm mode
    • 13.3.36. ethernet cfm raw-vlan
    • 13.3.37. ethernet cfm lm enable dual-ended
    • 13.3.38. ethernet cfm lm enable single-ended
    • 13.3.39. ethernet cfm lm single-ended
    • 13.3.40. show ethernet cfm lm
    • 13.3.41. ethernet cfm sd-reason
    • 13.3.42. ethernet cfm (1dm|dmm)
    • 13.3.43. ethernet cfm (1dm|dmm) continual
    • 13.3.44. show ethernet cfm dmm continual
    • 13.3.45. ethernet cfm delaymeasurement cache enable
    • 13.3.46. ethernet cfm delaymeasurement cache size
    • 13.3.47. show ethernet cfm delaymeasurement cache
    • 13.3.48. clear ethernet cfm delaymeasurement cache
    • 13.3.49. ethernet cfm csf
    • 13.3.50. show ethernet cfm csf
    • 13.3.51. ethernet cfm lck enable
    • 13.3.52. show ethernet cfm lck
    • 13.3.53. show ethernet cfm lm brief
    • 13.3.54. ethernet cfm tst transmission enable
    • 13.3.55. ethernet cfm tst start/stop
    • 13.3.56. ethernet cfm tst reception enable
    • 13.3.57. show ethernet cfm tst
    • 13.3.58. clear ethernet cfm tst counters
  • 13.4. CPU Traffic Limit Commands
    • 13.4.1. cpu-traffic-limit total rate
    • 13.4.2. cpu-traffic-limit reason rate
    • 13.4.3. cpu-traffic-limit reason class
    • 13.4.4. show cpu traffic-limit
  • 13.5. CPU Traffic Statistics Commands
    • 13.5.1. cpu-traffic-statistics time
    • 13.5.2. no cpu-traffic-statistics time
    • 13.5.3. show cpu traffic- statistics receive
    • 13.5.4. show cpu traffic-statistics receive all
    • 13.5.5. show cpu traffic-statistics transmit
  • 13.6. CPU Traffic Protect Commands
    • 13.6.1. cpu-traffic-protect
    • 13.6.2. trace enable
    • 13.6.3. trace type
    • 13.6.4. trace sample
    • 13.6.5. trace threshold
    • 13.6.6. trace timeout
    • 13.6.7. trace action
    • 13.6.8. trace protect delay-time
    • 13.6.9. apply access-list
    • 13.6.10. cpu-traffic-protect manual recover dhcp
    • 13.6.11. show cpu traffic-protect dhcp recover table
    • 13.6.12. show cpu traffic-protect trace
    • 13.6.13. show cpu traffic-protect trace config
    • 13.6.14. clear cpu traffic-protect trace
  • 13.7. UDLD Commands
    • 13.7.1. udld enable
    • 13.7.2. udld port
    • 13.7.3. udld message interval
    • 13.7.4. udld reset
    • 13.7.5. show udld
    • 13.7.6. show udld neighbors
    • 13.7.7. debug udld
    • 13.7.8. show debugging udld
  • 13.8. ERPS Commands
    • 13.8.1. erps
    • 13.8.2. erps control vlan
    • 13.8.3. erps hellotime
    • 13.8.4. erps failtime
    • 13.8.5. erps mstp instance
    • 13.8.6. erps ring level
    • 13.8.7. erps ring mode
    • 13.8.8. erps ring primary interface
    • 13.8.9. erps ring secondary interface
    • 13.8.10. erps ring interface
    • 13.8.11. erps ring edge-mode
    • 13.8.12. erps ring edge interface
    • 13.8.13. erps ring common interface
    • 13.8.14. erps ring srpt
    • 13.8.15. erps ring enable
    • 13.8.16. erps ring disable
    • 13.8.17. erps enable
    • 13.8.18. erps disable
    • 13.8.19. erps mode rrpp
    • 13.8.20. show erps
    • 13.8.21. show erps list
    • 13.8.22. clear erps counters
    • 13.8.23. debug erps
  • 13.9. Smart-Link Commands
    • 13.9.1. smart-link group
    • 13.9.2. smart-link relay enable
    • 13.9.3. interface
    • 13.9.4. protected mstp instance
    • 13.9.5. load-balance instance
    • 13.9.6. restore time
    • 13.9.7. restore enable
    • 13.9.8. flush send
    • 13.9.9. group enable
    • 13.9.10. smart-link flush receive
    • 13.9.11. smart-link tcn enable
    • 13.9.12. smart-link tcn query-count
    • 13.9.13. smart-link tcn query-interval
    • 13.9.14. show smart-link
    • 13.9.15. show smart-link group
    • 13.9.16. clear smart-link statistic
    • 13.9.17. debug smart-link
  • 13.10. Multi-Link Commands
    • 13.10.1. multi-link group
    • 13.10.2. multi-link relay enable
    • 13.10.3. interface
    • 13.10.4. protected mstp instance
    • 13.10.5. load-balance instance
    • 13.10.6. restore time
    • 13.10.7. restore enable
    • 13.10.8. flush send
    • 13.10.9. group enable
    • 13.10.10. multi-link flush receive
    • 13.10.11. multi-link tcn enable
    • 13.10.12. multi-link tcn query-count
    • 13.10.13. multi-link tcn query-interval
    • 13.10.14. show multi-link
    • 13.10.15. show multi-link group
    • 13.10.16. clear multi-link statistic
    • 13.10.17. debug multi-link
    • 13.10.18. multilink-enhance interface
    • 13.10.19. multilink-enhance receive
    • 13.10.20. multilink-enhance send-interval
    • 13.10.21. multilink-enhance timeout
  • 13.11. Monitor Link Commands
    • 13.11.1. monitor-link group
    • 13.11.2. monitor-link uplink interface
    • 13.11.3. monitor-link uplink smart-link group
    • 13.11.4. no monitor-link uplink
    • 13.11.5. monitor-link downlink interface
    • 13.11.6. monitor-link recover-time
    • 13.11.7. show monitor-link group
    • 13.11.8. debug monitor-link
  • 13.12. VRRP Commands
    • 13.12.1. advertisement-interval
    • 13.12.2. advertisement-interval msec
    • 13.12.3. interface (VRRP)
    • 13.12.4. learnmaster-mode
    • 13.12.5. preempt-mode
    • 13.12.6. preempt delay
    • 13.12.7. priority (VRRP)
    • 13.12.8. router vrrp
    • 13.12.9. track (VRRP)
    • 13.12.10. enable /disable
    • 13.12.11. virtual-ip
    • 13.12.12. show vrrp
  • 13.13. Track Commands
    • 13.13.1. delay up
    • 13.13.2. delay down
    • 13.13.3. frequency
    • 13.13.4. ip sla monitor
    • 13.13.5. description string
    • 13.13.6. ip sla monitor schedule
    • 13.13.7. timeout
    • 13.13.8. threshold
    • 13.13.9. interval
    • 13.13.10. ttl
    • 13.13.11. tos
    • 13.13.12. data-size
    • 13.13.13. data-pattern
    • 13.13.14. fail-percent
    • 13.13.15. packets-per-test
    • 13.13.16. statistics (packet \|test)
    • 13.13.17. clear ip sla statistics
    • 13.13.18. track
    • 13.13.19. track interface linkstate
    • 13.13.20. track rtr reachability
    • 13.13.21. track rtr state
    • 13.13.22. track bfd
    • 13.13.23. track cfm
    • 13.13.24. type icmp-echo
    • 13.13.25. show ip sla monitor
    • 13.13.26. show track
    • 13.13.27. vrf
  • 13.14. VARP Commands
    • 13.14.1. ip virtual-router mac
    • 13.14.2. ip virtual-router address
    • 13.14.3. ipv6 virtual-router address
  • 13.15. IP BFD Commands
    • 13.15.1. bfd interval
    • 13.15.2. bfd NAME peer-ip A.B.C.D interface
    • 13.15.3. bfd NAME peer-ip A.B.C.D source-ip
    • 13.15.4. ip route
    • 13.15.5. bfd set interval
    • 13.15.6. bfd global dscp
    • 13.15.7. bfd set dscp
    • 13.15.8. show bfd
    • 13.15.9. show bfd static configurations
    • 13.15.10. show bfd session
    • 13.15.11. show resource bfd static configurations
    • 13.15.12. show bfd interface
    • 13.15.13. show bfd add-fail-session
• 14. Device Management Commands
• 15. Network Management Commands
  • 15.1. Network Diagnosis Commands
    • 15.1.1. ping
    • 15.1.2. traceroute
  • 15.2. NTP Commands
    • 15.2.1. ntp ace
    • 15.2.2. ntp authentication
    • 15.2.3. ntp disable
    • 15.2.4. ntp key
    • 15.2.5. ntp interface reload
    • 15.2.6. ntp max-distance
    • 15.2.7. ntp peer
    • 15.2.8. ntp refclock
    • 15.2.9. ntp server
    • 15.2.10. ntp trustedkey
    • 15.2.11. show ntp
    • 15.2.12. show ntp ace
    • 15.2.13. show ntp associations
    • 15.2.14. show ntp key
    • 15.2.15. show ntp status
    • 15.2.16. show ntp statistics
    • 15.2.17. clear ntp statistics
    • 15.2.18. ntp mgmt-if
  • 15.3. Phy Loopback Commands
    • 15.3.1. loopback phy
    • 15.3.2. loopback port
    • 15.3.3. no loopback
    • 15.3.4. show phy loopback
    • 15.3.5. l2 ping
    • 15.3.6. l2 ping response
    • 15.3.7. show l2ping response
    • 15.3.8. show l2ping state
    • 15.3.9. l2 ping stop
    • 15.3.10. l2 ping forward enable
    • 15.3.11. debug l2ping
    • 15.3.12. show debugging l2ping
  • 15.4. RMON Commands
    • 15.4.1. rmon collection stats
    • 15.4.2. rmon collection history
    • 15.4.3. rmon event
    • 15.4.4. rmon alarm
    • 15.4.5. show rmon statistics
    • 15.4.6. show rmon history
    • 15.4.7. show rmon event
    • 15.4.8. show rmon alarm
    • 15.4.9. rmon clear counters
    • 15.4.10. debug rmon
  • 15.5. SNMP Commands
    • 15.5.1. snmp-server access
    • 15.5.2. snmp-server community
    • 15.5.3. snmp-server context
    • 15.5.4. snmp-server enable
    • 15.5.5. snmp-server engineID
    • 15.5.6. snmp-server group
    • 15.5.7. snmp-server notify
    • 15.5.8. snmp-server system-contact
    • 15.5.9. snmp-server system-location
    • 15.5.10. snmp-server target-address
    • 15.5.11. snmp-server target-params
    • 15.5.12. snmp-server trap enable
    • 15.5.13. snmp-server trap delay
    • 15.5.14. snmp-server trap target-address
    • 15.5.15. snmp-server trap source-address
    • 15.5.16. snmp-server inform target-address
    • 15.5.17. snmp-server inform
    • 15.5.18. snmp-server version
    • 15.5.19. snmp-server view
    • 15.5.20. snmp-server access-group NAME in
    • 15.5.21. show snmp
    • 15.5.22. show snmp-server access
    • 15.5.23. show snmp-server community
    • 15.5.24. show snmp-server context
    • 15.5.25. show snmp-server engineID
    • 15.5.26. show snmp-server group
    • 15.5.27. show snmp-server notify
    • 15.5.28. show snmp-server sys-info
    • 15.5.29. show snmp-server trap-receiver
    • 15.5.30. show snmp-server usm-user
    • 15.5.31. show snmp-server version
    • 15.5.32. show snmp-server view
  • 15.6. SFLOW Commands
    • 15.6.1. sflow enable
    • 15.6.2. sflow agent
    • 15.6.3. sflow collector
    • 15.6.4. sflow counter interval
    • 15.6.5. sflow counter-sampling enable
    • 15.6.6. sflow flow-sampling rate
    • 15.6.7. sflow flow-sampling enable
    • 15.6.8. show sflow
  • 15.7. LLDP Commands
    • 15.7.1. lldp enable(global)
    • 15.7.2. lldp enable(interface)
    • 15.7.3. lldp system-name
    • 15.7.4. lldp system-description
    • 15.7.5. lldp management
    • 15.7.6. lldp msg-tx-hold
    • 15.7.7. lldp timer msg-tx-interval
    • 15.7.8. lldp timer reinit-delay
    • 15.7.9. lldp timer tx-delay
    • 15.7.10. lldp tlv basic
    • 15.7.11. lldp tlv 8021-org-specific
    • 15.7.12. lldp tlv 8021-org-specific vlan-name-value
    • 15.7.13. lldp tlv 8023-org-specific
    • 15.7.14. lldp tlv med
    • 15.7.15. lldp tlv med location-id
    • 15.7.16. debug lldp
    • 15.7.17. show lldp local
    • 15.7.18. show lldp neighbor
    • 15.7.19. show lldp statistics
    • 15.7.20. clear lldp statistics
  • 15.8. IPFIX Commands
    • 15.8.1. ipfix recorder
    • 15.8.2. description
    • 15.8.3. match ipv4
    • 15.8.4. match ipv6
    • 15.8.5. match mac
    • 15.8.6. match transport
    • 15.8.7. match vlan
    • 15.8.8. match cos
    • 15.8.9. match interface (input | output)
    • 15.8.10. match vxlan-vni
    • 15.8.11. match nvgre-key
    • 15.8.12. match transport tcp flags
    • 15.8.13. match packet (drop | non-drop)
    • 15.8.14. collect counter
    • 15.8.15. collect flow
    • 15.8.16. collect ttl
    • 15.8.17. collect quality
    • 15.8.18. collect timestamp
    • 15.8.19. ipfix exporter
    • 15.8.20. description
    • 15.8.21. destination
    • 15.8.22. dscp
    • 15.8.23. domain-id
    • 15.8.24. source interface
    • 15.8.25. template data timeout
    • 15.8.26. flow data timeout
    • 15.8.27. transport protocol
    • 15.8.28. ttl
    • 15.8.29. event flow
    • 15.8.30. ipfix sampler
    • 15.8.31. description
    • 15.8.32. 1 out-of
    • 15.8.33. ipfix monitor (global)
    • 15.8.34. description
    • 15.8.35. recorder
    • 15.8.36. exporter
    • 15.8.37. flow mirror
    • 15.8.38. ipfix monitor (interface/port-group/vlan group)
    • 15.8.39. ipfix global configure
    • 15.8.40. ipfix global flow
    • 15.8.41. ipfix hardware-telemetry enable
    • 15.8.42. ipfix hardware-telemetry dest
    • 15.8.43. show ipfix recorder
    • 15.8.44. show ipfix exporter
    • 15.8.45. show ipfix cache
    • 15.8.46. show ipfix monitor
    • 15.8.47. show ipfix sampler
    • 15.8.48. show resource ipfix
    • 15.8.49. clear ipfix cache monitor
    • 15.8.50. clear ipfix cache observe-point interface
  • 15.9. Hardware Monitor Commands
    • 15.9.1. hardware monitor watermark
    • 15.9.2. show hardware monitor watermark interface
    • 15.9.3. hardware monitor notify server
    • 15.9.4. hardware monitor notify interval
    • 15.9.5. hardware buffer-monitor notify
    • 15.9.6. hardware latency-monitor notify
    • 15.9.7. show hardware monitor statistics
    • 15.9.8. hardware buffer-monitor
    • 15.9.9. hardware buffer-monitor micro-burst
    • 15.9.10. hardware buffer-monitor micro-burst threshold
    • 15.9.11. show hardware buffer-monitor status
    • 15.9.12. show hardware buffer-monitor interface
    • 15.9.13. show hardware buffer-monitor micro-burst interface
    • 15.9.14. hardware latency-monitor
    • 15.9.15. hardware latency-monitor threshold event
    • 15.9.16. hardware latency-monitor range
    • 15.9.17. hardware latency-monitor drop
    • 15.9.18. hardware latency-monitor threshold drop
    • 15.9.19. show hardware latency-monitor status
    • 15.9.20. show hardware latency-monitor interface
    • 15.9.21. show hardware latency-monitor event interface
• 16. VPN Commands
  • 16.1. VRF Commands
    • 16.1.1. ip vrf
    • 16.1.2. show ip vrf
    • 16.1.3. ip vrf forwarding
    • 16.1.4. ip route vrf
    • 16.1.5. arp vrf
    • 16.1.6. show ip arp vrf
    • 16.1.7. clear ip arp vrf
    • 16.1.8. ping vrf
    • 16.1.9. traceroute vrf
    • 16.1.10. telnet vrf
    • 16.1.11. rd
    • 16.1.12. route-target
    • 16.1.13. import map
    • 16.1.14. export map
    • 16.1.15. router-id
    • 16.1.16. description
    • 16.1.17. show resource vrf
  • 16.2. GRE TUNNEL Commands
    • 16.2.1. interface
    • 16.2.2. tunnel mode gre
    • 16.2.3. tunnel source
    • 16.2.4. tunnel destination
    • 16.2.5. tunnel enable
    • 16.2.6. tunnel gre key
    • 16.2.7. tunnel dscp
    • 16.2.8. keepalive
    • 16.2.9. show interface tunnel
    • 16.2.10. show resource tunnel
    • 16.2.11. show tunnel keepalive statistics
    • 16.2.12. clear tunnel keepalive statistics
    • 16.2.13. clear tunnel statistics
  • 16.3. ERSPAN TUNNEL Commands
    • 16.3.1. interface
    • 16.3.2. tunnel mode erspan
    • 16.3.3. tunnel source
    • 16.3.4. tunnel destination
    • 16.3.5. tunnel ecmp-destination
    • 16.3.6. tunnel gre key
    • 16.3.7. tunnel dscp
    • 16.3.8. tunnel ttl
    • 16.3.9. tunnel extend-header
    • 16.3.10. tunnel extend-header id
    • 16.3.11. tunnel extend-header dst-load-balance
    • 16.3.12. show resource tunnel
• 17. Network Virtualization Commands
  • 17.1. Overlay Commands
    • 17.1.1. vlan overlay enable
    • 17.1.2. overlay
    • 17.1.3. vlan vni
    • 17.1.4. vni split-horizon-disable
    • 17.1.5. source
    • 17.1.6. remote-vtep
    • 17.1.7. dscp-strategy
    • 17.1.8. Virtual-mac
    • 17.1.9. vlan remote-vtep
    • 17.1.10. overlay uplink
    • 17.1.11. vxlan uplink
    • 17.1.12. nvgre uplink
    • 17.1.13. mac-address-table forward remote-vtep
    • 17.1.14. gateway-mac
    • 17.1.15. ip route remote-vtep
    • 17.1.16. overlay distributed-gateway
    • 17.1.17. selective qinq overlay mode
    • 17.1.18. vxlan udp-dest-port
    • 17.1.19. qos tunnel-aware inner
    • 17.1.20. qos tunnel-aware inner-outer-merge
    • 17.1.21. Show overlay
  • 17.2. EVPN Commands
    • 17.2.1. address-family l2vpn evpn
    • 17.2.2. debug overlay evpn
    • 17.2.3. evpn
    • 17.2.4. overlay host-collect
    • 17.2.5. rd
    • 17.2.6. route-target
    • 17.2.7. route-target evpn
    • 17.2.8. neighbor attribute-unchanged
    • 17.2.9. neighbor send-community
    • 17.2.10. neighbor route-reflector-client
    • 17.2.11. retain route-target all
    • 17.2.12. advertise l2vpn evpn
    • 17.2.13. vni
    • 17.2.14. vxlan vni
    • 17.2.15. vxlan uplink
    • 17.2.16. interface nve
    • 17.2.17. source
    • 17.2.18. member vni
    • 17.2.19. dscp-strategy
    • 17.2.20. virtual-mac
    • 17.2.21. keep-vlan-tag
    • 17.2.22. split-horizon
    • 17.2.23. evpn Inclusive multicast
    • 17.2.24. vlan arp-broadcast-suppress
    • 17.2.25. evpn mode
    • 17.2.26. vlan mac-address-tunnel learning-disable
    • 17.2.27. show bgp evpn
    • 17.2.28. show bgp evpn instance
    • 17.2.29. show bgp evpn neighbors
    • 17.2.30. show overlay host-information
    • 17.2.31. show interface nve
    • 17.2.32. show overlay tunnel
    • 17.2.33. show overlay evpn remote-vtep
    • 17.2.34. show overlay mac-forwarding-information
• 18. Intelligent Lossless Network Commands
  • 18.1. PFC Commands
    • 18.1.1. priority-flow-control mode
    • 18.1.2. priority-flow-control enable priority
    • 18.1.3. show priority-flow-control
    • 18.1.4. show priority-flow-control statistics
    • 18.1.5. priority-flow-control deadlock precision
    • 18.1.6. priority-flow-control deadlock priority
    • 18.1.7. priority-flow-control deadlock limit priority
    • 18.1.8. show priority-flow-control deadlock status
    • 18.1.9. show priority-flow-control deadlock statistics
    • 18.1.10. clear priority-flow-control deadlock statistics
  • 18.2. EFD Commands
    • 18.2.1. efd enable
    • 18.2.2. efd tcp-only enable
    • 18.2.3. efd flow-traffic-class
    • 18.2.4. efd flow-color
    • 18.2.5. efd detect speed
    • 18.2.6. efd detect granularity
    • 18.2.7. efd detect time-interval
    • 18.2.8. efd detect min-pkt-size
    • 18.2.9. efd aging-period
    • 18.2.10. efd redirect to interface
    • 18.2.11. efd ipg enable
    • 18.2.12. efd notify enable
    • 18.2.13. efd notify packet
    • 18.2.14. efd black-hole-route gw
    • 18.2.15. efd black-hole-route aging-timer
    • 18.2.16. efd syslog enable
    • 18.2.17. show efd bhr information
    • 18.2.18. show efd configuration
    • 18.2.19. show efd flow table
    • 18.2.20. show efd flow information
    • 18.2.21. clear efd flow information
• 19. PoE Commands
  • 19.1. PoE configuration commands
    • 19.1.1. poe global
    • 19.1.2. poe power-management policy
    • 19.1.3. poe power-reserved
    • 19.1.4. poe power-threshold
    • 19.1.5. poe enable|disable
    • 19.1.6. poe priority
    • 19.1.7. poe max-power
    • 19.1.8. poe legacy
    • 19.1.9. poe forced-power
    • 19.1.10. clear poe counters
  • 19.2. PoE show commands
    • 19.2.1. show poe summary
    • 19.2.2. show poe status
    • 19.2.3. show poe schedule
    • 19.2.4. show poe counters

References

• Search Page

• Index